Filter
Top Products
NOTE: The holes in the top and
middle clamp will line up only
when assembled correctly.
3. Place the clamps and the
handlebar over the shaft housing
and onto the bottom clamp.
4. Hold each hex nut in the
bottom clamp recess with a
finger. Start screws with a
large Phillips screwdriver. Do
not tighten until you make the
handle adjustment.
5. While holding the unit in the
operating position (Fig. 2),
move the handlebar to the
location that provides you the
best grip.
6. Tighten the clamp screws evenly, until the handlebar is secure.
4
Cutting
Attachment
Shield
Throttle
Control
Bull Horn
Handlebar
Cutting
Attachment
Shaft
Grip
Fuel
Cap
Blue
Choke
Lever
Shaft
Housing
Starter Rope Grip
Line
Cutting
Blade
Spark
Plug
Muffler
On/Off Stop
Control
Air Filter/
Muffler
Cover
Cutting
Blade
KNOW YOUR UNIT
Foot
Stand
Primer
Bulb
OIL AND FUEL INFORMATION
WARNING:
Remove fuel cap slowly to avoid injury
from fuel spray. Never operate the unit without the
fuel cap securely in place.
WARNING: Add fuel in a clean, well ventilated
outdoor area. Wipe up any spilled fuel immediately.
Avoid creating a source of ignition for spilt fuel. Do
not start the engine until fuel vapors dissipate.
Using Fuel Additives
The bottle of 2-cycle oil
that came with your unit
contains a fuel additive
which will help inhibit
corrosion and minimize the
formation of gum deposits.
It is recom-mended that
you use our 2-cycle oil with
this unit.
If unavailable, use a good
2-cycle oil designed for
air-cooled engines along with a fuel additive, such as STA-BIL
®
Gas Stabilizer or an equivalent. Add 0.8 oz. (23 ml.) of fuel additive
per gallon of fuel according to the instructions on the container.
NEVER add fuel additives directly to the unit's fuel tank.
NOTE: Dispose of the old fuel/oil mix in accordance to
Federal, State and Local regulations.
Definition of Blended Fuels
Today's fuels are often a blend of gasoline and oxygenates
such as ethanol, methanol, or MTBE (ether). Alcohol-blended
fuel absorbs water. As little as 1% water in the fuel can make
fuel and oil separate and leads to formation of acids during
storage. When using alcohol-blended fuel, use fresh fuel.
UNLEADED GAS
2-CYCLE OIL
+
UNLEADED GAS 2 CYCLE OIL
1 GALLON US 3.2 FL. OZ.
(3.8 LITERS) (95 ml)
1 LITER 25 ml
MIXING RATIO - 40:1
CAUTION: For proper engine operation and
maximum reliability, pay strict attention to the oil
and fuel mixing instructions on the 2-cycle oil
container. Using improperly mixed fuel can severely
damage the engine.
Using Blended Fuels
If you choose to use a blended fuel, or its use is unavoidable,
follow recommended precautions:
• Always use the fresh fuel mix explained in the operator's manual
• Always shake the fuel mix before fueling the unit
• Drain the tank and run the engine dry before storing the unit
Applications
As a trimmer, cutting grass and light weeds, and decorative
trimming around trees, fences, etc.
As a brushcutter, cutting weeds and light bush of up to 13 mm
(1/2 inch) in diameter
ASSEMBLY INSTRUCTIONS
INSTALL AND ADJUST THE HANDLEBAR
1. Place the bull-horn handle between the top and middle
clamp pieces (Fig. 1).
2. While holding the three pieces together, install the four (4)
screws through the top clamp and into middle clamp.
(4) Screws
Top
Clamp
Middle Clamp
Bottom
Clamp
Nuts
Fig. 1
Fig. 2
Throttle
Lock-Out