Meade NG-Series Telescope User Manual


 
20
General Maintenance
Your telescope is a precision optical instrument designed to yield a lifetime of reward-
ing applications. Given the care and respect due any precision instrument, your tele-
scope will rarely require factory servicing or maintenance. Maintenance guidelines
include:
1. Avoid cleaning the telescope’s optics. A little dust on the front surface of the tele-
scope’s lens causes virtually no degradation of image quality and should not be
considered reason to clean the lens.
2. When absolutely necessary, dust on the front lens should be removed with gen-
tle strokes of a camel hair brush or blown off with an ear syringe (available at any
pharmacy
). Do not use a commercial photographic lens cleaner.
3. Organic materials (
e.g., fingerprints) on the front lens may be removed with a
solution of 3 parts distilled water to 1 part isopropyl alcohol. A single drop of
biodegradable dishwashing soap may be added per pint of solution. Use soft,
white facial tissues and make short, gentle strokes. Change tissues often.
CAUTION: Do not use scented, colored or lotioned tissues as damage
could result to the optics.
4. If your telescope is used outdoors on a humid night, telescope surfaces may
accumulate water condensation. While such condensation does not normally
cause any damage to the telescope, it is recommended that the entire telescope
be wiped down with a dry cloth before being packed away. Do not, however, wipe
any of the optical surfaces. Rather, simply allow the telescope to sit for some time
in warm indoor air, so that the wet optical surfaces can dry unattended. In addi-
tion, the dust cap should not be placed back on to the optical tube until the tele-
scope is thoroughly dry.
5 If your telescope is not to be used for an extended period, perhaps for one month
or more, it is advisable to remove the 9v battery from inside the base. Batteries
left installed for prolonged periods may leak, causing damage to the telescope’s
electronic circuitry.
6. Do not leave your telescope outdoors on a warm day or inside a sealed car for
an extended period of time. Excessive ambient temperatures can damage the
telescope’s internal lubrication and electronic circuitry.
Adjusting the Horizontal and Vertical Tension of the Optical
Tube
If the horizontal and/or vertical movement of the optical tube seems to be too loose or
too tight, you can adjust the amount of tension in the movement of the optical tube to
suit your own preference. To adjust the horizontal tension of the optical tube, use an
adjustable wrench or nut driver to tighten or loosen the horizontal adjustment nut
located under the base of the telescope. See Fig. 13.
To adjust the vertical tension of the optical tube, first loosen the attachment knobs (
5,
Fig. 1
) and remove the optical tube from the bracket (3, Fig. 1). Use an adjustable
wrench or nut driver to tighten or loosen the vertical adjustment nut located on the
inner side of the bracket. See Fig. 14. Check the amount of tension by moving the
bracket up and down before reattaching the optical tube.
Storage and Transport
When not in use, store the telescope in a cool, dry place. Do not expose the instru-
ment to excessive heat or moisture. It is best to store the telescope in its original box.
If shipping the telescope, use the original box and packing material to protect the tel-
escope during shipment.
When transporting the telescope, take care not to bump or drop the instrument; this
type of abuse can damage the optical tube and/or the objective lens.
Troubleshooting
Unable to see an image through the eyepiece:
Confirm that the dust cap has been removed from the telescope.
Images through the eyepiece appear unfocused or distorted:
The magnification used may be too high for the seeing conditions. Back off to a
lower power eyepiece. See
TOO MUCH POWER? page 10.
MAINTENANCE AND SERVICING
Fig. 13: Horizontal adjustment nut.
(View of the underside of the base.)
Horizontal
adjustment
nut
Fig. 14:Vertical adjustment nut.
(Bracket shown with optical tube
removed.)
Vertical
adjustment
nut