Filter
Top Products
Caring for your Hedgetrimmer
Cleaning (K)
• USE GLOVES
1. Using a soft brush - remove debris from all air
intakes and cutting blade.
2. Wipe over surface of your hedgetrimmer with
a dry cloth.
• IMPORTANT
Never use water for cleaning your
hedgetrimmer. Do not clean with chemicals,
including petrol, or solvents - some can
destroy critical plastic parts.
Lubricating the Cutting Blade
For easier operation and longer life, lubricate the
cutter blades before and after use. Apply the oil so
that it runs between the two blades. See Pic L.
At the end of the Cutting Season.
1. Clean your Hedgetrimmer thoroughly.
2. Check that all nuts and bolts are secure.
3. Visually inspect the Hedgetrimmer for any worn
or damaged parts, contact your local Service
Centre if any parts require replacement.
To store your Hedgetrimmer
• The Hedgetrimmer blade cover/storage holder
is provided with 2 hanging slots for storing the
Hedgetrimmer on the wall. (M)
• Ensure the blade cover/storage holder is fitted
before storage.
1. The use of 2 number 10 screws (40mm in length)
and the appropriate wall fixing plugs is recommended
2. Drill 2 horizontal holes 47mm apart.
3. Fit wall plugs.
4. Fit screw ensuring enough length is available
for secure location into hanging slot.
• Your mains cable can be stored with the blade
cover/storage holder fitted. (Pic N & P)
• Store in a dry place where your hedgetrimmer
is protected from damage.
Fault Finding Hints
Fails to Operate
1. Is the Power Turned On?
2. Check the fuse in the plug, if blown replace.
3. Fuse continues to blow?
Disconnect from the mains electricity supply
and consult your local approved Electrolux
Outdoor Products Service Centre.
Cutting blade stops under load
1. Cut at a slower pace.
2. If cutting blade still stops under load?
Disconnect from the mains electricity supply
and consult your local approved Electrolux
Outdoor Products Service Centre.
Cutting blade stops under load
1. Cut at a slower pace.
2. If cutting blade still stops under load?
Disconnect from the mains electricity supply
and consult your local approved Electrolux
Outdoor Products Service Centre.
Fails to stop when one switch lever is released.
Disconnect from the mains electricity supply
and consult your local approved Electrolux
Outdoor Products Service Centre.
Poor cut quality
1. Ensure the product is being used correctly
(see How to Use)
2. Ensure blades are free from trapped debris
3. Damaged Blades?
Disconnect from the mains electricity supply
and consult your local approved Electrolux
Outdoor Products Service Centre.
Excessive Vibration
Disconnect from the mains electricity supply
and consult your local approved Electrolux
Outdoor Products Service Centre.
ENGLISH - 3
How to Use
How to Use your Hedgetrimmer
1. Inspect area to be cut before each use -
remove objects which can be thrown or
become entangled in the cutting blades.
2. Always keep the Hedgetrimmer in front of your
body. Hold handle firmly with both hands and
stand in a secure and stable position.
3. Allow the cutting blades to reach full speed
before entering the material to be cut.
4. Always work going away from people and
solid objects such as walls, large stones,
trees, vehicles etc.
5. If blade stalls, immediately stop the
Hedgetrimmer. Disconnect the Hedgetrimmer
from the power source and clear jammed
debris from the cutting blades. Inspect blades
and repair or replace as needed.
Top Cutting
Use a wide sweeping motion. (Fig. H) A slight
downward tilt of the cutting blades in the
direction of motion gives the best cutting results.
Side Cutting
When trimming the sides of the hedge, begin at
the bottom and cut upwards (Fig. J), tapering the
hedge inward at the top. This shape will expose
more of the hedge, resulting in more uniformed
growth.