Makita BCM2600 Brush Cutter User Manual


 
3
5. Maintenance
Any warranted part which is not scheduled for replacement as
required maintenance or which is scheduled only for regular inspec-
tion to the effect of “repair or replace as necessary” shall be war-
ranted as to defects for the warranty period. Any warranted part
which is scheduled for replacement as required maintenance shall be
warranted as to defects only for the period of time up to the first
scheduled replacement for that part. Any replacement part that is
equivalent in performance and durability may be used in the perfor-
mance of any maintenance or repairs. The owner is responsible for
the performance of all required maintenance, as defined in the Makita
owner’s manual.
6. Consequential Coverage
Coverage hereunder shall extend to the failure of any engine compo-
nents caused by the failure of any warranted part still under warranty.
EMISSIONS COMPONENT DEFECT WARRANTY COVERAGE
MAKITA U.S.A. Inc. (MAKITA) warrant to the initial retail purchaser
and each subsequent owner, that this utility equipment was
designed, built, and equipped to conform at the time of initial sale to
all applicable regulations of the U.S. Environmental Protection
Agency (EPA), and that the engine is free of defects in materials and
workmanship which would cause this engine to fail to conform with
EPA regulations during its warranty period.
For the components listed under PARTS COVERED, the service
dealer authorized by MAKITA will, at no cost to you, make the neces-
sary diagnosis, repair, or replacement necessary to ensure that the
engine complies with applicable U.S. EPA regulations.
EMISSISON COMPONENT DEFECT WARRANTY PERIOD
The warranty period for this engine begins on the date of sale to the
initial purchaser and continues for a period of 2 years.
PARTS COVERED
Listed below are the parts covered by the Emission Components
Defect Warranty. Some of the parts listed below may require sched-
uled maintenance and are warranted up to the first scheduled
replacement point for that part.
(1) Fuel Metering System
(i) Carburetor and internal parts
(ii) Fuel filter, if applicable.
(iii) Throttle stopper, if applicable.
(iv) Choke System, if applicable.
(2) Air Induction System
(i) Air cleaner plate
(ii) Air cleaner case
(3) Ignition System
(i) Spark plugs.
(ii) Flywheel Magneto
(iii) Ignition Coil.
(4) Miscellaneous Items Used in Above Systems
(i) Fuel hoses, clamps and sealing gaskets
OBTAINING WARRANTY SERVICE
To obtain warranty service, take your engine to the nearest MAKITA
Factory Service Center or service Center authorized by MAKITA.
Bring your sales receipts indicating date of purchase for this engine.
The dealer of service authorized by MAKITA will perform the neces-
sary repairs or adjustments within a reasonable amount of time and
furnish you with a copy of the repair order. All parts and accessories
replaced under this warranty become the property of MAKITA.
WHAT IS NOT COVERED
• Conditions resulting from tampering, misuse, improper adjustment
(unless they were made by the service dealer authorized by MAKITA
during a warranty repair), alteration, accident, failure to use the rec-
ommended fuel and oil, or not performing required maintenance
services.
- The replacement parts used for required maintenance services.
- Consequential damages such as loss of time, inconvenience,
loss of use of the engine or equipment, etc.
- Diagnosis and inspection charges that do not result in war-
ranty-eligible service being performed.
- Any non-authorized replacement part, or malfunction of autho-
rized parts due to use of non-authorized parts.
OWNER’S WARRANTY RESPONSIBILITIES
As the engine owner, you are responsible for the performance of the
required maintenance listed in your owner's manual. MAKITA recom-
mends that you retain all receipts covering maintenance on your
engine, but MAKITA cannot deny warranty solely for the lack of
receipts or for your failure to ensure the performance of all sched-
uled maintenance. As the engine owner, you should however be
aware that MAKITA may deny warranty coverage if your engine or a
part has failed due to abuse, neglect, improper maintenance or unap-
proved modifications.
You are responsible for presenting your engine to the nearest service
dealer authorized by MAKITA when a problem exists.
If you have any questions regarding your warranty rights and respon-
sibilities, you should contact the followings :
* For the nearest Makita service center, please visit
www.makitatools.com
* For technical support or questions regarding operation of our tools
and accessories call: 1-800-4-MAKITA
* Makita USA Inc. Corporate Office : 14930 Northam St. La Mirada, CA
90638-5753
(For Canada)
* For the authorized service centre nearest you please refer to the
local yellow pages directory under “tools”, or contact our customer
service department Tel 1-800-263-3734 (Canada only), or visit our
web site www.makita.ca
* Makita Canada Inc. Head Office & Plant : 1950 Forbes Street,
Whitby, ON L1N 7B7
THINGS YOU SHOULD KNOW ABOUT THE EMISSION
CONTROL SYSTEM WARRANTY:
MAINTENANCE AND REPAIRS
You are responsible for the proper maintenance of the engine. You
should keep all receipts and maintenance records covering the per-
formance of regular maintenance in the event questions arise.
These receipts and maintenance records should be transferred to
each subsequent owner of the engine. MAKITA reserves the right to
deny warranty coverage if the engine has not been properly main-
tained. Warranty claims will not be denied, however, solely because
of the lack of required maintenance or failure to keep maintenance
records.
MAINTENANCE, REPLACEMENT OR REPAIR OF EMISSION CON-
TROL DEVICES AND SYSTEMS MAY BE PERFORMED BY ANY
REPAIR ESTABLISHMENT OR INDIVIDUAL; HOWEVER, WARRANTY
REPAIRS MUST BE PERFORMED BY A SERVICE DEALER AUTHO-
RIZED BY MAKITA. THE USE OF PARTS THAT ARE NOT EQUIVA-
LENT IN PERFORMANCE AND DURABILITY TO AUTHORIZED PARTS
MAY IMPAIR THE EFFECTIVENESS OF THE EMISSION CONTROL
SYSTEM AND MAY HAVE A BEARING ON THE OUTCOME OF A WAR-
RANTY CLAIM.
If other than the parts authorized by MAKITA are used for mainte-
nance replacements or for the repair of components affecting emis-
sion control, you should assure yourself that such parts are
warranted by their manufacturer to be equivalent to the parts autho-
rized by MAKITA in their performance and durability.
HOW TO MAKE A CLAIM
All repair qualifying under this limited warranty must be performed
by a service dealer authorized by MAKITA. In the event that any emis-
sion-related part is found to be defective during the warranty period,
you shall notify MAKITA at the following contacts and you will be
advised of the appropriate warranty service dealer or service provid-
ers where the warranty repair can be performed.
* For the nearest Makita service center , please visit
www.makitatools.com
* For technical support or questions regarding operation of our tools
and accessories call: 1-800-4-MAKITA
* Makita USA Inc. Corporate Office : 14930 Northam St. La Mirada, CA
90638-5753
(For Canada)
* For the authorized service centre nearest you please refer to the
local yellow pages directory under “tools”, or contact our customer
service department Tel 1-800-263-3734 (Canada only), or visit our
web site www.makita.ca
* Makita Canada Inc. Head Office & Plant : 1950 Forbes Street,
Whitby, ON L1N 7B7