Filter
Top Products
23
Pre-lter (foam with air-lter oil)
Only for models DPC8131 and 8132
Clean or replace (when cutting with high dust amounts):
• Daily
or at least every
• 4 operating hours, or
• 8 tank llings, or
• 8 litres fuel mixture.
Clean or replace (when cutting wet, or when cutting steel):
• weekly
or at least every
• 25 operating hours, or
• 50 tank llings, or
• 55 litres fuel mixture.
Cleaning: Cleaning: Rinse off coarse dirt in running water.
Knead a capful MAKITA lter cleaner (Order No. 980 008 627
into the foam material of the pre-lter (1, Order No. 395 173
090) until it suds up well.
Rinse out pre-lter thoroughly in running water.
Let the pre-lter dry thoroughly.
In order to ensure full ltration effectiveness, air-lter
oil must be used with the pre-lter. Wet the pre-lter
with a capful (about 20 ccm) of MAKITA air-lter oil
(Order No. 980 008 628, biodegradable).
Knead the pre-lter to evenly distribute the oil. Then
squeeze out any excess oil.
NOTE: If using other air-lter oils, follow the manufacturer’s
instructions.
If cleaning is not possible on-site, have spare pre-lters on
hand (Order No. 395 173 090).
To insert the pre-lter in the lter cover, position it so it ts the
space in the cover and then press it in (5). The pre-lter must
t completely and cover all parts of the lter space, without
leaving any spaces unltered.
Inner lters (all models)
Wash out the dirty inner lter (3, Order No. 395 173 020)
in lukewarm soapy water with regular dishwashing liquid or
MAKITA lter cleaner (Order No. 980 008 627).
Let the inner lter dry thoroughly.
Air lter insert (paper cartridge, all models)
The air lter insert (2, Order No. 395 173 010) lters the intake
air through a very ne paper lter lamella system. For the rea-
son the cartridge must never be washed. Clean the air lter
insert once a week.
To clean the air lter insert, spread it out slightly and carefully
tap it against a clean surface.
Replace the air lter insert every 100 operating hours. Replace
it immediately if there is a drop in power, drop in speed, or
smoke in the exhaust.
Before installing the lter system, check the intake opening to
make sure no dirt particles have fallen in. If they have, remove
them.
CAUTION: Turn off the engine before cleaning the air lter! Never clean out the air lter with compressed air! Do
not clean the pre-lter and inner lter with fuel.
The service life of the engine depends on the condition and regular maintenance of the lter elements. Failure to
perform maintenance and cleaning at the prescribed intervals will cause increased wear inside the engine!
If the air lter becomes damaged, replace immediately! Pieces of cloth or large dirt particles can destroy the engine!
Do not work in dusty conditions when it can be avoided! The ne dust generated when dry-cutting concrete and stone
is hazardous to the health of the operator and also shortens the service life of the engine. Whenever possible, wet-cut
with water when working in concrete and stone, to bind the dust.
Pre-lter (dry foam)
Only for models DPC6340-7341
If the pre-lter (1, Order No. 395 173 080) is dirty, wash
it out in lukewarm water with standard dishwashing liquid
or MAKITA lter cleaner (Order No. 980 008 627). If using
MAKITA lter cleaner, proceed as described after the text
section "Cleaning".
Let the pre-lter dry thoroughly.
NOTE: The pre-lter must be cleaned daily, or several times
daily if working under dusty conditions. If cleaning is not
possible on-site, have spare pre-lters on hand. Replace the
pre-lter at least every 25 operating hours.
To improve ltration effectiveness, the pre-lter can be wet-
ted with air-lter oil. Before adding air-lter oil, carefully
wash the lter with air-lter cleaner. Care for the oiled air
lter as described for DPC8131, 8132.
To insert the pre-lter in the lter cover, position it so it ts
the space in the cover and then press it in (5). The pre-lter
must t completely and cover all parts of the lter space,
without leaving any spaces unltered.