Filter
Top Products
For 4190DB (Fig. 4)
Plug the battery charger into your power source.
Insert the battery cartridge so that theplus and minus
terminals on the battery cartridge are on the same
sides as their respective markings on the battery
charger. Insert the cartridge fully into the port so that
it rests on the charger port floor.
When the battery cartridge is inserted, the charging
light will come on and charging will begin. The charg-
ing light will keep lighting up steadily during charging.
When charging is completed, the charging light goes
out. The charging time is approx. 100 minutes.
After charging, unplug the charger from the power
source.
Battery type
Capacity
(mAh)
Number of
cells
9033 2,200 8
CAUTION:
•
If you charge a battery cartridge from a just-
operated machine or a battery cartridge which has
been left in a location exposed to direct sunlight for
a long time,the charging light mayflash in red color.
If this occurs, wait for a while. Charging will begin
after the battery cartridge cools.
•
Any of the following conditions indicates damage to
the charger and/or battery cartridge. Ask your
Makita Authorized or Factory Service Center to
check them.
1) The charging light does not light up or flash (red)
when the battery is inserted in the charger port.
2) Charging is not completed at even more than
three hours after red light comes ON at start of
charging.
Trickle charge (Maintenance charge)
If you leave the battery cartridge in the charger to
prevent spontaneous discharging after full charge,
the charger will switch into its ‘‘trickle charge (main-
tenance charge)’’ mode and keep the battery car-
tridge fresh and fully charged.
Tips for maintaining maximum battery life
1. Charge the battery cartridge before completely
discharged.
Always stop machine operation and charge the
battery cartridge when you notice less machine
power.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3. Charge the battery cartridge with room tempera-
ture at 10°C – 40°C (50°F – 104°F).
Let a hot battery cartridge cool down before
charging it.
Installing water supply
Attach the tank holder on the tank. The tank holder
should be attached aroundthe portion shown with the
dotted line.Tightenthe screw(A) to theextent thatthe
tank can still turn within the tank holder. (Fig. 5)
Attach the tank holder onto the motor housing.
Tighten the screw (B) securely. (Fig. 6)
Connect the cap on the end of the polyvinyl tube to
the mouth of the tank. Turn the tank clockwise when
making the connection. Then tighten the screw (A)
securely to secure the tank. (Fig. 7)
CAUTION:
If you find the polyvinyl tube is bent like a ‘‘V’’ or has
been strained excessively after installing the water
supply,loosen the screw(B) and adjustthe position of
the tank to alleviate the bent, pinched or strained
condition.
Installing or removing diamond wheel
(Fig.8&9)
Important:
Always be sure that the machine is switched off and
the battery cartridge is removed before installing or
removing the wheel.
To install the wheel, first loosen the bolt with the hex
wrench and remove the bolt and the flange. Then
mount the wheel, the flange and the bolt. The wheel
should be mounted with the Makita name on the
flange side.
Press the blade stopper pin and insert it through the
hole in the wheel so that the wheel cannot revolve.
Use the hex wrench to tighten the bolt securely.
To removethe wheel, followthe installation procedure
in reverse.
CAUTION:
•
When installingthe wheel,be sureto tightenthe bolt
securely.
•
Use only the Makita hex wrench to install or remove
the wheel.
Hex wrench storage (Fig. 10)
When not in use, the hex wrench can be conveniently
stored.
Adjusting depth of cut (Fig. 11)
Loosen the bolt (A) on the depth guide with the hex
wrench andmove the base upor down.At thedesired
depth of cut, secure the base by tightening the bolt
(A).
Bevel cutting (Fig. 12)
Loosenthe bolt(A) onthe depthguide andthe bolt(B)
on the bevel scale plate with the hex wrench. Set for
the desired angle (0 – 45°) bytilting accordingly, then
tighten the bolts (A) and (B) securely.
CAUTION:
After adjusting depth of cut and bevel cutting angle,
be sure to tighten the bolts (A) and (B) securely.
Sighting (Fig. 13)
For straight cuts, align the edge of the base with your
cutting lineon the workpiece.For 45°bevel cuts, align
the notch in the front of the base with it.
CAUTION:
When making bevel cuts, view the cutting line on the
workpiece through the window in the blade case in
order to cut more accurately. If you have difficulty
seeing it because of the water tank, adjust the posi-
tion of the tank by tilting it backward slightly.
6
4190D (E) (’100. 3. 15)