Filter
Top Products
BATTERY REPLACEMENT
1. Remove the battery cover by sliding the cover down.
2. Observing the correct polarity install 2 AAA batteries. The batteries will fit
tightly (to avoid start-up problems make sure they do not spring free).
3. Do not mix old and new batteries.
4. Do not mix alkaline, lithium, standard or rechargeable batteries.
5. Replace the battery cover by sliding upwards.
Be sure battery cover is on securely.
LOW BATTERY INDICATOR
When batteries are low, the low battery indicator shows up on the LCD. You will
receive an e-mail or mobile text message alert when the battery power of the
sensor is low. Change the batteries immediately.
Note: The LED turns ON briefly after changing batteries. The LED turns OFF
when not needed to save battery power. The previously stored information in
the sensor will not be affected or cancelled while you change the batteries.
MOUNTING
Select a location where the transmitter may be installed.
Protected from water and rain as the transmitter is water resistant not water
proof.
Within range of the wireless gateway (see “IMPORTANT SETUP & OPERATION
NOTES”).
If mounting within the control area of a hot tub, mount the transmitter far from
the electrical motor that drives the pumps which create electrical noise that
may interfere with transmission of the temperature signal.
IMPORTANT! TEST the transmitter in the selected mounting location for 1
hour before alterations are made to your property.
Check signal reception to the wireless gateway.
Note:
The sensor can be used without the probe wire for ambient
temperature/humidity.
The probe sensor can be used as a stand-alone product. Simply insert the
probe wire into the water of your hot tub and secure the transmitter in an
area that is protected from water. The transmitter case is water resistant but
not waterproof.
The fine threaded probe sensor can be secured in a bolt hole to prevent
movement.
IMPORTANT: Before inserting the threaded probe into a bolt
hole it is recommended to cover the threads with 3 layers of
Teflon tape (not included).
*CAUTION!* Do not alter or change your property until you have
considered all options for installation. Assess your specific hot
tub/spa construction to determine if additional plumbing supplies
(not included) would be needed to install the probe.
La Crosse Technology is not responsible for alterations made by
the homeowner to their property.
Select what temperature you wish to monitor:
Actual water temperature
Heater water temperature
Cabinet temperature
THE TX60U-IT TEMPERATURE & HUMIDITY SENSOR
The sensor can be mounted onto a wall with the use of screws
MOUNTING WITH SCREWS
1. Remove the mounting bracket from the sensor.
2. Place the mounting bracket over the desired location.
3. Mark mounting surface with a pencil through the 2 holes of the bracket.
4. Screw mounting bracket onto surface and tighten screws to bracket.
5. Insert the sensor into the bracket.
TABLE STANDING AND OTHER MOUNTING OPTIONS
With the mounting bracket installed at the bottom or on the top of
the sensor, the user can place it on any flat surface.
Note: Before permanently fixing the sensor mounting bracket, place
all units in the desired locations to check that the outdoor
temperature & humidity readings are receivable. In event that the
signal is not received, relocate the sensor or move them slightly as
this may help the signal reception.
MAINTENANCE AND CARE
Avoid extreme temperatures, vibration, and shock to prevent damage.
Clean displays and units with a soft, damp cloth. Do not use solvents or
scouring agents; they may mark the displays and casings.
Do not submerge the sensor case in water.
Avoid kinking the temperature probe cable.
Immediately remove all low powered batteries to avoid leakage and damage.
Opening the casings invalidates the warranty. Do not try to repair the unit.
Contact La Crosse Technology® for repairs.
SPECIFICATIONS
Device sensor:
Temperature range:
-40°F to 140°F with 0.2°F resolution
“OFL” displayed if outside this range.
Humidity measuring range:
3% to 99%
Transmission range:
200 feet (60.96 m) in open space
**Optional probe sensor:
Temperature range:
-40°F to 140°F with 0.2°F resolution
“OFL” displayed if outside this range, and
displayed “nC” if probe is not connected.
Power Supply:
Temperature transmitter :
2 x AAA, IEC LR03, 1.5V
Battery life cycle:
Approximately 24 months
Recommended battery type:
Alkaline
Dimensions (H x W x D):
5.23" x 0.76" x 1.44"
WARRANTY INFORMATION
La Crosse Technology, Ltd provides a 1-year limited warranty on this product
against manufacturing defects in materials and workmanship.
This limited warranty begins on the original date of purchase, is valid only on
products purchased and used in North America and only to the original
purchaser of this product. To receive warranty service, the purchaser must
contact La Crosse Technology, Ltd for problem determination and service
procedures. Warranty service can only be performed by a La Crosse
Technology, Ltd authorized service center. The original dated bill of sale must
be presented upon request as proof of purchase to La Crosse Technology, Ltd
or La Crosse Technology, Ltd’s authorized service center.
La Crosse Technology, Ltd will repair or replace this product, at our option and
at no charge as stipulated herein, with new or reconditioned parts or products if
found to be defective during the limited warranty period specified above. All
replaced parts and products become the property of La Crosse Technology, Ltd
and must be returned to La Crosse Technology, Ltd. Replacement parts and
products assume the remaining original warranty, or ninety (90) days,
whichever is longer. La Crosse Technology, Ltd will pay all expenses for labor
and materials for all repairs covered by this warranty. If necessary repairs are
not covered by this warranty, or if a product is examined which is not in need or
repair, you will be charged for the repairs or examination. The owner must pay
any shipping charges incurred in getting your La Crosse Technology, Ltd
product to a La Crosse Technology, Ltd authorized service center. La Crosse
Technology, Ltd will pay ground return shipping charges to the owner of the
product to a USA address only.
Your La Crosse Technology, Ltd warranty covers all defects in material and
workmanship with the following specified exceptions: (1) damage caused by
accident, unreasonable use or neglect (including the lack of reasonable and
necessary maintenance); (2) damage occurring during shipment (claims must
be presented to the carrier); (3) damage to, or deterioration of, any accessory or
decorative surface; (4) damage resulting from failure to follow instructions
contained in your owner’s manual; (5) damage resulting from the performance
of repairs or alterations by someone other than an authorized La Crosse
Technology, Ltd authorized service center; (6) units used for other than home
use (7) applications and uses that this product was not intended or (8) the
products inability to receive a signal due to any source of interference.. This
warranty covers only actual defects within the product itself, and does not cover
the cost of installation or removal from a fixed installation, normal set-up or
adjustments, claims based on misrepresentation by the seller or performance
variations resulting from installation-related circumstances.
LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY FOR
INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR
DAMAGES ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF
THIS PRODUCT. THIS PRODUCT IS NOT TO BE USED FOR MEDICAL
PURPOSES OR FOR PUBLIC INFORMATION. THIS PRODUCT IS NOT A
TOY. KEEP OUT OF CHILDREN’S REACH.
This warranty gives you specific legal rights. You may also have other rights
specific to your State. Some States do not allow the exclusion of consequential
or incidental damages therefore the above exclusion of limitation may not apply
to you.
For warranty work, technical support, or information, please contact:
La Crosse Technology, Ltd
2817 Losey Blvd. S.
La Crosse, WI 54601