Filter
Top Products
Specifications with Quick-Coupler
and Hook-On Construction Fork 624K TOOL CARRIER
▲ Tine Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.22 m (48 in.) 1.52 m (60 in.)
Fork Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.52 m (60 in.) 2.29 m (90 in.)
▲▲ Overall Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.02 m (26 ft. 4 in.) 8.33 m (27 ft. 4 in.)
Tipping Load, Straight (fork level, load centered
and positioned at 50% tine length) . . . . . . . . . . 9555 kg (21,065 lb.) 8946 kg (19,723 lb.)
Tipping Load, 40-Deg. Full Turn (fork level,
load centered and positioned at 50%
tine length). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8303 kg (18,305 lb.) 7755 kg (17,096 lb.)
Operating Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 955 kg (32,971 lb.) 15 094 kg (33,277 lb.)
Loader operating information is based on machine with identified linkage and standard equipment, ROPS cab, rear cast bumper/counterweight, transmission side-frame guards, bottom guards, standard tires,
full fuel tank, and 79-kg (175 lb.) operator. This information is affected by changes in tires, ballast, and different attachments, and assumes no tire deflection per the standard ISO 14397-1 section 5.
Adjustments to Operating Weights and Tipping Loads with Buckets
Adjustments to operating weights and tipping loads are based on tool-carrier machine and pin-on 2.7-m
3
(3.5 cu. yd.) general-purpose bucket with bolt-on cutting edge, ROPS cab, rear cast
bumper/counterweight, transmission side-frame guards, bottom guards, standard tires, full fuel tank, and 79-kg (175 lb.) operator*
Add (+) or deduct (–) lb. (kg) as indicated for Tipping Load, 40-
loaders with 3-piece rims and Operating Weight Tipping Load, Straight Deg. Full Turn, SAE
20.5 R 25, 1 Star L-3 . . . . . . . . . . . . . . . . . . . . . . 0 kg (0 lb.) 0 kg (0 lb.) 0 kg (0 lb.)
20.5 R 25, 1 Star L-2 . . . . . . . . . . . . . . . . . . . . . . – 148 kg (– 326 lb.) – 103 kg (– 227 lb.) – 91 kg (– 200 lb.)
20.5-25, 16 PR L-2 . . . . . . . . . . . . . . . . . . . . . . . – 324 kg (– 714 lb.) – 225 kg (– 496 lb.) – 198 kg (– 437 lb.)
20.5-25, 16 PR L-3 . . . . . . . . . . . . . . . . . . . . . . . – 228 kg (– 503 lb.) – 158 kg (– 349 lb.) – 139 kg (– 308 lb.)
600/65 R 25, 1 Star L-3T
§
. . . . . . . . . . . . . . . . . . + 42 kg (+ 93 lb.) + 39 kg (+ 86 lb.) + 35 kg (+ 76 lb.)
28L-26 Logger
†
. . . . . . . . . . . . . . . . . . . . . . . . . . + 406 kg (+ 895 lb.) + 292 kg (+ 643 lb.) + 257 kg (+ 567 lb.)
CaCl
2
in 20.5-25, L-3 rear tires . . . . . . . . . . . . . . + 1166 kg (+ 2,571 lb.) + 1627 kg (+ 3,586 lb.) + 1433 kg (+ 3,159 lb.)
*May change based on vehicle configuration, weight, or tire-pressure adjustments.
§
CaCl
2
not recommended.
†
Equipped with one-piece rims.
Bucket Selection Guide*
624K TOOL-CARRIER LOADER WITH PIN-ON BUCKET
BUCKET SIZE m
3
(cu. yd.)
0.8 (1.0)
4.6 (6.0)
4.2 (5.5)
3.8 (5.0)
3.4 (4.5)
3.0 (4.0)
2.7 (3.5)
2.3 (3.0)
1.9 (2.5)
1.5 (2.0)
1.1 (1.5)
4.9 (6.5)
lb./cu. yd.
kg/m
3
1,000 2,000 3,000 4,000 5,000 7,0006,0001,500 2,500 3,500 4,500 5,500 6,500 7,500
3600 42003000240018001200
600 900 1500 2100 2700 3300 3900
LOOSE MATERIALS
Chips, pulpwood
Cinders (coal, ashes, clinkers)
Clay and gravel, dry
Clay, compact, solid
Clay, dry in lump loose
Clay, excavated in water
Coal, anthracite, broken, loose
Coal, bituminous, moderately wet
Earth, common loam, dry
Earth, mud, packed
Granite, broken
Gypsum
Limestone, coarse, sized
Limestone, mixed sizes
Limestone, pulverized or crushed
Sand, damp
Sand, dry
Sand, voids, full of water
Sandstone, quarried
Shale, broken crushed
Slag, furnace granulated
Stone or gravel, 37.5 to 87.5-mm
(1.5 to 3.5") size
Stone or gravel, 18.75-mm (3/4") size
lb./cu. yd.
486
1,134
2,700
2,943
1,701
2,160
1,458
1,350
2,052
3,105
2,592
3,834
2,646
2,835
2,295
3,510
2,970
3,510
2,214
2,295
3,294
2,430
2,700
kg/m
3
288
673
1602
1746
1009
1282
865
801
1218
1843
1538
2275
1570
1682
1362
2083
1762
2083
1314
1362
1955
1442
1602
This guide, representing bucket sizes not necessarily manufactured by
Deere, will help you in selecting proper bucket size for material density,
loader configuration, and operating conditions. Optimum bucket size
is determined after adding or subtracting all tipping load changes due
to optional equipment. The “conservative load” line on this guide is
recommended when operating in conditions such as soft ground and
unlevel surfaces. The “maximum load” condition on this guide is
sometimes utilized when operating on firm ground and level surfaces.
*
Deere 2.7-m
3
(3.5 cu. yd.) General-Purpose Bucket
C
o
n
s
e
r
v
a
t
i
v
e
L
o
a
d
N
o
r
m
a
l
L
o
a
d
M
a
x
i
m
u
m
L
o
a
d
Vertis QCA
1300 19th Street, Suite 200
East Moline, IL 61244
Cyan
Magenta
Yellow Black
40 DKAKULDR Page 41