Filter
Top Products
DKA244JCWP Litho in U.S.A. (09-03)
Net engine power is with standard equipment including air
cleaner, exhaust system, alternator, and cooling fan at test
conditions per ISO9249. No derating is required up to 5,000-ft.
(1500 m) altitude.
Specifications and design subject to change without notice. Wherever applicable, specifications are in accordance with SAE
standards. Except where otherwise noted, these specifications are based on a unit with all standard equipment, 365/70R18 tires,
ROPS cab, full fuel tank, and 175-lb. (79 kg) operator.
244J
Engine
●
Certified to EPA interim Tier 4 emissions
● Antifreeze, –34°F (–37°C)
● Coolant recovery tank
● Fan safety guard
● Fan, suction type, hydraulically driven, propor-
tional speed
● Muffler, under hood with curved end exhaust stack
● Environmentally friendly engine oil drain
● Spin-on engine oil and fuel filter
● Engine oil cooler
● Quick-release fuel filter and water separator
● Under-hood dual-element air cleaner with restric-
tion indicator
● Above-hood prescreened air intake with dust
evacuator valve
● Serpentine drive belt with automatic tensioner
▲ Engine coolant heater, 750 watts, 110 volts
▲ Special application: Trash screens, etc.*
Electrical
●
Starter switch with electric fuel cutoff
● 12-volt system
● Electrical load center with blade-type fuses
● Standard batteries (2), 12 volt with 1,700 CCA
● Master electrical disconnect switch
● Alternator, 12 volts, 65 amps
● Horn (conforms to SAE J994, J1446)
● Lights (conform to SAE 99): Driving / Front working
(2) / Turn signals / Flashers / Stop / Taillights
● Pre-wired for rear worklights
▲ Worklights, rear (2)
● Reverse warning alarm (conforms to SAE J994,
J1446)
● Multifunction monitor with audible and visual
warnings: Low engine oil pressure / Engine coolant
temperature / HST transmission oil temperature /
Parking brake indicator / Gauges and indicators:
Engine coolant temperature, fuel level, speedom-
eter, clock, and hour meter
● Indicator lights: Engine air filter / Fasten seat belt /
Parking brake actuated / Forward/reverse travel /
1st or 2nd speed range / Turn signal and hazard
lights / High-beam indicator / Battery voltage
244J
Electrical (continued)
● Radio-ready cab, fused 12-volt radio electrical
lead and speakers, power port
● By-pass starter safety cover on starter, positive
terminal battery cover
● Pre-wired for roof beacon
● Sealed external electrical connectors
Powertrain/Brakes
●
Hydrostatic (HST) transmission: Electric shift con-
trol / Single-lever joystick F-N-R / Hydrostatic oil
cooler / Inching pedal / Two speeds forward and
reverse / Infinitely variable speed control
● Service brakes, hydraulically actuated, self-
adjusting internal wet-disk brake and driveline
drum brake
● Parking brake, spring applied, hydraulically
released, switch operated
● Axles, manual locking front and conventional rear
differentials, heavy-duty outboard planetaries
Hydraulic System
●
Hydraulic system oil cooler
● Automatic bucket return-to-dig control
● Boom float function
● Reservoir sight gauge for hydraulic/hydrostatic oil
● Fine-micron hydraulic filter, vertical mounting
● Hydraulic lever lockout
● Pilot-operated three-function valve with single
joystick lever control for boom and bucket, and
auxiliary lever for standard pin disconnect and
auxiliary hydraulics
▲ Four-function hydraulic valve with pilot joystick
control and pilot auxiliary lever for third function,
and push buttons for fourth function
▲ Hydraulic conversion kits, four-function valve
● Quick-coupler diagnostic ports: Priority pressure /
Hydraulic pump pressure / Control valve pressure /
HST pressure
Operator’s Station
●
Cab (conforms to SAE J1040, SAE J231, ISO3471,
ISO3449): ROPS/FOPS / Heater/defroster / Rubber-
plane isolation mounted for noise/vibration reduc-
tion / Intermittent front and rear windshield wipers
and washers / Tinted safety glass / Full-width
244J
Operator’s Station (continued)
adjust able sun visor / Pre-wired for radio speak-
ers / Deluxe high-back cloth seat with mechanical
suspension and 2-inch (51 mm) retractable seat
belt / Left and right doors / One sliding window in
each door
▲ AM/FM/WB radio
▲ AM/FM/WB radio with cassette player
▲ AM/FM/WB radio with CD player
▲ Air conditioning (factory or dealer installed)
● Storage compartment
● Rubber floormat
● Tilt steering column
● Rearview mirrors, outside (2) and inside (1) (con-
form to SAE J985)
● Handholds and steps, ergonomically located and
slip resistant (conform to SAE J185)
Loader Linkage
●
Z-bar loader linkage
● Loader boom service locking bar (conforms to
SAE J38)
Buckets and Attachments
▲ Full line of buckets with selection of bolt-on
cutting edges
● Standard quick-coupler, less bucket
▲ Pallet fork for standard quick-coupler
▲ Worksite Pro
TM
skid-steer-style coupler
▲ Full line of construction utility forks, pallet forks,
extendible boom with hook, and other attachments*
Tires
●
365/70R18 tires on single-piece rims
▲ 400/70R20 tires on single-piece rims
Other
●
Fenders, front and rear
● Articulation locking bar (conforms to SAE J276)
● Vandal protection, includes lockable engine enclo-
sure and fuel fill
● Counterweight, full
● Rear bottom guard
● Drawbar, with locking pin
▲ Material-weighing system*
▲ Ride control
▲ JDLink
TM
wireless communication system
244J LOADER
Key: ● Standard equipment ▲ Optional or special equipment *See your John Deere dealer for further information.
CONTROL OWNING AND OPERATING COSTS
Customer Personal Service (CPS) is part of John Deere’s proactive, fix-before-fail strat-
egy on machine maintenance that will help control costs, increase profits, and reduce
stress. Included in this comprehensive lineup of ongoing programs and services are:
Fluid analysis program – tells you what’s going on inside all of your machine’s
major components so you’ll know if there’s a problem before you see a decline in
performance. Fluid analysis is included in most extended coverage and preventive-
maintenance agreements.
Component life-cycle data – gives you vital information on the projected life
span of components and lets you make informed decisions on machine maintenance
by telling you approximately how many hours of use you can expect from an engine,
transmission, or hydraulic pump. This information can be used to preempt catastrophic
downtime by servicing major components at about 80 percent of their life cycle.
Preventive Maintenance (PM) agreements – give you a fixed cost for maintain-
ing a machine for a given period of time. They also help you avoid downtime by ensur-
ing that critical maintenance work gets done right and on schedule. On-site preventive
maintenance service performed where and when you need it helps protect you from
the expense of catastrophic failures and lets you avoid waste-disposal hassles.
Extended coverage – gives you a fixed cost for machine repairs for a given period
of time so you can effectively manage costs. Whether you work in a severe-service
setting or just want to spread the risk of doing business, this is a great way to custom-
fit coverage for your operation. And an extended coverage contract also travels well
because it’s backed by John Deere and is honored by all Deere construction dealers.
Customer Support Advisors (CSAs) – Deere believes the CSA program lends a
personal quality to Customer Personal Service (CPS). Certified CSAs have the knowledge
and skills for helping make important decisions on machine maintenance and repair.
Their mission is to help you implement a plan that’s right for your business and take
the burden of machine maintenance off your shoulders.
Vertis QCA
1300 19th Street, Suite 200
East Moline, IL 61244
Cyan
Magenta
Yellow Black
DKA244JCWP Page 18
Black