Filter
Top Products
Type Liquid-cooled, inline, 3-cylinder, normally aspirated
industrial diesel engine
Starter 12-volt (1.2 kw), solenoid shift positive
engagement
Charging System 12-volt, 40-amp alternator
Oil Filter Remote-mounted, spin-on engine oil filter (oil
pan and filter can be drained into a single drain container
for easy maintenance and minimal clean up) 5.1 qt
(4.8 l) oil capacity
Engine Oil 10W40
Fuel #2 diesel
Fuel Filter Heavy-duty, spin-on fuel filter
Injection System Bosch in-line
Air Filter Heavy-duty air filter with safety filter for maxi-
mum protection
Cooling Liquid cooled. Direct-driven,
mechanical cooling fan
Governor Mechanical governor with 3000 RPM
high idle speed
Traction Drive System
Type Dual hydrostatic drive includes tandem 21 cc Hydro-
Gear PW pumps, Hydro-Gear PRM Series wheel motors,
and an auxiliary oil cooler w/electric fan. Pumps are driven
directly from crankshaft with a micro-V-belt.
Hydraulic Oil 10W40
Filter 30 micron in tank
Ground Speed Infinitely variable: 0-12 mph (0-19.3 kph)
forward, 0-7 mph (0-11 kph) reverse
Steering SmoothTrak™ twin-lever steering with patented
automatic park brake system provides independent control
of each drive wheel. Speed, forward, reverse, brake, and
turns are all controlled with hand-operated controls
Turning Radius True zero turning radius. Turns within its
own length. Counter-rotating, independent drive wheels
Brakes Service: Hydrostatic dynamic braking
Parking: Internal friction brake in each PRM wheel motor
Mower Drive Single V-belt drive from engine with Warner
electric CMS 250 enhanced spot brake clutch. Spring ten-
sion idler for extended belt life.
Tires Front: 13 x 6.50 – 6, rib tread
Drive: 23 x 9.50 – 12, turf tread (54” deck)
24 x 12 – 12, turf tread (with 60 in – 72 in deck)
Capacities Fuel System: 15 US gal (57 l)
Hydraulic Oil: 7 qts (6.6 l)
Engine Coolant: 6 US qts (5.7 l)
601542 3-08
Hustler Turf Equipment • Hesston, Kansas 67062 • 1-800-395-4757
For more information : www.hustlerturf.com
Dimensions Height: 51 in (130 cm) ROPS folded down
69 in (175 cm) ROPS up
W/54 in XR-7 Deck Length: 86 in (218 cm)
Overall width: 55 in (140 cm) w/discharge chute up
Tire-to-tire width: 52 in (132 cm)
Weight: 1568 lbs (711 kg)
W/60 in XR-7 Deck Length: 86 in (218 cm)
Overall width: 61 in (155 cm) w/discharge chute up
Tire-to-tire width: 56 in (142 cm)
Weight: 1600 lbs (726 kg)
W/66 in XR-7 Deck Length: 88 in (224 cm)
Overall width: 67 in (170 cm) w/discharge chute up
Tire-to-tire width: 56 in (142 cm)
Weight: 1642 lbs: (745 kg)
W/72 in XR-7 Deck Length: 90 in (229 cm)
Overall width: 73 in (185 cm) w/discharge chute up
Tire-to-tire width: 56 in (142 cm)
Weight: 1684 lbs: (764 kg)
Safety Features: Standard foldable ROPS. Operator pres-
ence system connected to seat, deck clutch and park brake
switches. Stabilizer rollers at rear of tractor.
Seat: Suspension, molded-vinyl, adjustable seat with arm-
rests. Fore and aft adjustment
Construction Main frame is 1.5 in x 3 in x .187 in (3.8 cm
x 7.62 cm x .47 cm) rectangular steel tubing Drive motors
mounted to 7 ga (.45 cm) welded steel Front caster wheels
mounted with roller bearings on each wheel. Front caster
forks are .5 in (1.27 cm) steel
Deck Lift Foot-operated deck height adjustment. Pin for
setting height, detent for transport position
Controls Hand-operated throttle, ignition switch, electric
mower clutch. Integrated parking brakes.
Indicators Hour meter, high temp light, oil pressure light,
charge light, glow plug light, audible alarm for high engine
temperature and low oil pressure, electronic fuel gauge for
each tank.
Cup Holder Two cup holders molded into the left side fuel
tank. Accommodates nearly any cup size.
Decks 54”, 60”, 66”or 72” XR-7™ Side-Discharge or
54”, 60”, or 72” Rear-Discharge Decks
Type Free-floating mower using three blades with center
blade to the front. Mower is suspended at the corners.
Includes deck-mounted rollers to improve flotation in
rolling and uneven terrain.
Deck Lift Raise and lower deck from driver’s seat with
simple foot-operated deck height adjustment. Pin
for setting height, transport position. Change cutting
heights, climb curbs and trailer more easily.
Construction 7 ga welded steel. Solid 1 in x .375 in
(2.55 cm x .95 cm) steel bars reinforce impact areas on
trim edges. .187 in x .375 in (.47 cm x .95 cm) reinforced
front edge. Reinforcements welded onto spindle mount
areas.Steel deck housing is 5.5 in (14 cm) deep to pro-
vide room for high-capacity mowing.
Cutting Heights Foot-operated deck height adjustment.
Pin for setting height, detent for transport position.
Height adjustment in .25 in increments from 1 in to 5 in
(2.55 cm to 12.7 cm).
Mowing Blades Heavy-duty, heat-treated, high-lift
steel Fusion™ blades. Fusion blades feature an exclusive
electro-fusion technology that creates an ultra-hard
layer at the blade’s cutting edge, the blade remains
sharp and continues to give a clean cut far longer than
any blade on the market.
54 in: 18.50 in x 2.50 in x .203 in flat blade, high sail
60 in: 20.50 in x 2.50 in x .203 in flat blade, high sail
66 in: 22.50 in x 2.50 in x .203 in flat blade, high sail
72 in: 24.50 in x 2.50 in x .230 in flat blade, high sail
Blade Tip Speed 54 in: 18,322 fpm
60 in: 18,266 fpm
66 in: 18,964 fpm
72 in: 18,894 fpm
Blade Drive V-belt drive to all three spindles.
Spring tension idler pulleys.
Spindles Machined ductile iron housing, 1 in (2.5 cm)
dia. high carbon steel shafts and sealed ball bearings.
Flotation Suspended mower floats on four spring-
assisted chains. Anti-scalp wheels are standard.
Discharge Chute Molded Rubber:Over-center design
allows for chute to be folded up for improved trailering
or to pass thru gates, etc.
Width of Cut 54 in: 54 in (137 cm)
60 in: 60 in (152 cm)
66 in: 66 in (168 cm)
72 in: 72 in (183 cm)
Trim Capacity (left side)
54 in XR-7: 2 in (5.1 cm)
60 in XR-7: 2.9 in (7 cm)
66 in XR-7: 5.9 in (15 cm)
72 in XR-7: 8.9 in (23 cm)
Accessories
Mulch Kit Recycles clippings under deck allowing clip-
pings to be cut and recut, then discharged down into the
grass. Reduces handling of clippings, improves appear-
ance, and recycles nutrients back to the soil.
Hitch Kit Optional bolt-on hitch with 7/8-inch hole. Will
accept any standard ball.
Flex Forks™, Steering Extension Kit, Snow Blade
Hydraulic Deck Lift Kit, 3-Bag Catcher, Striping Kit,
Light Kit
Specifications subject to change without notice.
Hustler Z
™
Shibaura Diesel Specifications
Engine
Model SHIBAURA S773L
Horsepower 25
No. of Cylinders 3
Displacement (1.13 L)
Max. Torque 49 ft lbs (66 nm)
+
–
5% @ 2200 rpm
Hustler Turf Equipment Hustler Z
™
S h i b a u r a D i e s e l