Filter
Top Products
34 – English
Engine
Cylinder volume, cu.in/cm
3
Cylinder bore, inch/mm
Stroke, inch/mm
Idle speed, rpm
Power, kW/ rpm
Ignition system
Manufacture
Type of ignition system
Spark plug
Electrode gap, inch/mm
Fuel and lubrication
system
Manufacturer
Carburetor type
Fuel capacity, US pint/litre
Oil pump capacity at
8 500 rpm, ml/min
Oil capacity, US pint/litre
Type of oil pump
Weight
Without bar and chain, Lbs/kg
Chain/bar
Standard bar length,
inches/cm
Recommended bar lengths,
inches/cm
Usable cutting length
inches/cm
Chain speed at max.
power, m/sec
Pitch, inch/mm
Thickness of drive link,
inch/mm
Number of teeth on drive
sprocket
TECHNICAL DATA
45
2,7/44
1,65/42
1,26/32
2 500
2,2/ 9 000
Phelon
CD
Champion
RCJ 7Y
0,020/0,5
Zama
C1Q-EL5
1,06/0,5
8
0,53/0,25
Automatic
10,3/4,7
13"/33
13-18"/33-46
12,6-17,5"/
32-44,5
17,4
0,325"/8,25
0,050"/1,3
0,058"/1,5
7
49
3,0/49
1,73/44
1,26/32
2 500
2,3/ 9 000
Phelon
CD
Champion
RCJ 7Y,
NGK BPMR 7A
0,020/0,5
Zama
C1Q–EL5
1,06/0,5
8
0,53/0,25
Automatic
10,4/4,7
13"/33
13-20"/33-51
12,6-19,5"/
32-49,5
17,4
0,325"/8,25
0,050"/1,3
0,058"/1,5
7
Following is a list of recommended cutting equipment for the
Husqvarna Models 45 and 49. The combinations of powerhead,
bar and chain have been investigated in accordance with the
kickback requirements of ANSI B 175.1 – 1991. The guide bar
nose radius is determined by either the maximum number of teeth
in the nose sprocket or the corresponding maximum nose radius
of a solid bar.
The following list is the chain saw manufacturers
recommendations. There may be other combinations available,
which will also achieve kickback protection.
As we are listing the maximum guide bar nose radius, you may
use a guide bar with smaller nose radius than in our list. For guide
bars of the same length, all sprocket-nose guide bars of the same
pitch and having the same number of of sprocket teeth may be
considered to have equivalent kickback energy. A hard nose bar
having the same length and nose radius as a sprocket-nose bar
may be considered to have equivalent or less kickback energy
than the sprocket-nose bar.
Low kickback saw chain is a chain which is has met the kickback
performance requirements of ANSI B 175.1 safety requirements
for gasoline-powered chain saws when tested on the
representative sample of chain saws below 3.8 cu. in. specified in
ANSI B 175.1. We recommend that you as replacement use the
listed chains or "Low kickback saw chains" which are available at
your dealer.
Recommended bar and chain combinations
Guide bar Saw chain
Length Pitch Max nose
inch inch radius
13 0,325" 10T Husqvarna H30/H25 or
15 0,325" 10T Oregon 95VP/21VB
16 0,325" 10T
18 0,325" 10T
20 0,325" 12T Husqvarna H25 or Oregon 21VB
NOTE: The second number in the Oregon part number
indicate the thickness of the drive link. You are free to
choose between 0,050" and 0,058" drive link for the
corresponding bar.
OREGON 20 indicates 0,050"/1,3 mm
OREGON 21 indicates 0,058"/1,5 mm
´*3!3¶5B¨