Filter
Top Products
40 – English
TECHNICAL DATA
115 13 82-95 Rev.2 2009-03-23
Technical data
Recommended original and replacement bar and chain combinations
Following is a list of recommended cutting equipment for the Husqvarna chain saw model 455 Rancher. The
combinations of power head, bar and chain have been tested and found to be in accordance with the kickback and
vibration requirements of ANSI B175.1–2000.
The guide bar nose radius is determined by either the maximum number of teeth in the nose sprocket or the
corresponding maximum nose radius of a solid bar.
The following list is the chain saw manufacturers recommendations. There may be other combinations available, which
will also achieve kickback reduction.
As we are listing the maximum guide bar nose radius, you may use a guide bar with smaller nose radius than in our list.
For guide bars of the same length, all sprocket-nose guide bars of the same pitch and having the same number of
sprocket teeth may be considered to have equivalent kickback energy. A hard nose bar having the same length and nose
radius as a sprocket-nose bar may be considered to have equivalent or less kickback energy than the sprocket-nose bar.
Chain saw model Husqvarna 455 Rancher met the kickback performance requirements of ANSI B 175.1-2000 when tested
with the combinations of bars and saw chains listed below. The saw chains Husqvarna H30, H80 and H81 are also classified
as a low kickback saw chain since it met the requirements for low kickback saw chain outlined in ANSI B 175.1-2000. We
recommend to use only the listed combinations of bars and chains for chain saw model Husqvarna 455 Rancher. Other
chain saw models may not meet the kickback requirements when equipped with the listed bar and chain combinations.
455e Rancher 455 Rancher 460 Rancher
Engine
Cylinder displacement, cu.in/cm
3
3,38/55,5 3,38/55,5 3,68/60,3
Cylinder bore, inch/mm 1,85/47 1,85/47 1,93/49
Stroke, inch/mm 1,26/32 1,26/32 1,26/32
Idle speed, rpm 2700 2700 2700
Power, kW/hp @ rpm 2,6/3,5 @ 9000 2,6/3,5 @ 9000 2,7/3,7 @ 9000
Ignition system
Manufacturer of ignition system SEM SEM SEM
Type of ignition system CD CD CD
Spark plug
NGK BPMR 7A/
Champion RCJ 7Y
NGK BPMR 7A/
Champion RCJ 7Y
NGK BPMR 7A/
Champion RCJ 7Y
Electrode gap, inch/mm 0,02/0,5 0,02/0,5 0,02/0,5
Fuel and lubrication system
Manufacturer of carburetor Walbro Walbro Walbro
Carburetor type WTA WTA WTA
Fuel tank capacity, US pint/litre 0,93/0,44 0,93/0,44 0,93/0,44
Oil pump capacity at 9,000 rpm, ml/min 11,5 11,5 11,5
Oil tank capacity, US pint/litre 0,68/0,32 0,68/0,32 0,68/0,32
Type of oil pump Automatic Automatic Automatic
Weight
Chain saw without bar or chain, empty tanks, lb/kg 13,0/5,9 13,0/5,9 13,0/5,9
Chain/bar
Standard bar length, inch/cm 13"/33 13/33 13"/33
Recommended bar lengths, inch/cm 13-20"/33-50 13-20"/33-50 13-20"/33-50
Usable cutting length, inches/cm 12-19"/31-49 12-19"/31-49 12-19"/31-49
Pitch, inch/mm 0,325/8,25 0,325/8,25 0,325/8,25
Thickness of drive links, inch/mm 0,050/1,3 0,050/1,3 0,050/1,3
0,058/1,5 0,058/1,5 0,058/1,5
Drive sprocket type/teeth Spur/7 Spur/7 Spur/7
Chain speed at max. power, m/sec 17,3 17,3 17,3