Filter
Top Products
Page 3
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
READ AND UNDERSTAND ALL INSTRUCTIONS. Fail-
ure to follow all instructions listed below may result in
electric shock, fire, and/or serious personal injury.
READ THESE INSTRUCTIONS BEFORE USING
THIS BLOWER
Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases, or
dust. Power tools create sparks which may ignite the dust
or fumes.
To reduce the risk of electric shock, this tool has a po-
larized plug (one blade is wider than the other) and will
require the use of a polarized extension cord. The plug
will fit into a polarized extension cord only one way. If the
plug does not fit fully into the extension cord, reverse the
plug. If the plug still does not fit, obtain a correct polarized
extension cord. A polarized extension cord will require
the use of a polarized wall outlet. This plug will fit into the
polarized wall outlet only one way. If the plug does not fit
fully into the wall outlet, reverse the plug. If the plug still
does not fit, contact a qualified electrician to install the
proper wall outlet. Do not change the equipment plug,
extension cord receptacle, or extension cord plug in any
way.
Avoid body contact with grounded surfaces such as
pipes,
radiators, ranges, and refrigerators. There is an increased
risk of electric shock if your body is grounded.
Don’t expose power tools to rain or wet conditions. Wa-
ter entering a power tool will increase the risk of electric
shock.
Do not handle plug or tool with wet hands.
Use outdoor extension cords marked W-A, W,
SW-A,
SOW-A, STW-A, STOW-A, SJW-A, SJTW-A, or SJTOW-
A.
These cords are rated for outdoor use and reduce the
risk of electric shock.
Never allow children to operate the equipment. Never
allow adults to operate the equipment without proper
instruction.
Always wear safety glasses with side shields.
Everyday glasses have only impact resistant lenses. They
are NOT safety glasses. Following this rule will reduce the
risk of eye injury. Use face mask if operation is dusty.
Wear eye protection which is marked to comply with ANSI
Z87.1 when operating this product.
Wear heavy long pants, boots, and gloves. Avoid loose
garments or jewelry that could get caught in moving parts
of the machine or its motor.
Do not force tool. Use the correct tool for your applica-
tion. The correct tool will do the job better and safer at
the rate for which it is designed.
Do not operate the equipment while barefoot or when
wearing sandals or similar lightweight footwear. Wear
protective footwear that will protect your feet and improve
your footing on slippery surfaces.
Secure long hair so it is above shoulder level to prevent
entanglement in any moving parts.
Keep firm footing and balance. Do not overreach. Over-
reaching can result in loss of balance.
Avoid accidental starting. Be sure the power switch is not
on before plugging in. Turn off power switch before unplug-
ging.
Do not use tool if switch does not turn it on or off. Any
tool that cannot be controlled with the switch is danger-
ous and must be repaired.
Do not use with damaged plug. If tool is not working as
it should or has been dropped, damaged, left outdoors,
or dropped into water, return it to an authorized service
center.
Do not leave the tool when plugged in. Unplug from the
power outlet when not in use, before servicing, and be-
fore storing the tool. Such preventative safety measures
reduce the risk of starting the tool accidentally.
� Keep all bystanders, children, and pets at least 50 ft.
away.
� Do not operate this unit when you are tired, ill, or under
the influence of alcohol, drugs, or medication.
Do not operate in poor lighting.
� Keep all parts of your body away from any moving parts
and all hot surfaces of the unit.
� Do not put any object into openings. Do not use with any
opening blocked; keep openings free of dust, lint, hair,
and anything that may reduce air flow.
Check the work area before each use. Remove all objects
such as rocks, broken glass, nails, wire, or string which
can be thrown or become entangled in the machine.
� Use only identical manufacturer’s replacement parts and
accessories. Use of any other parts may create a hazard
or cause product damage.