Filter
Top Products
23 308-505
Servicing the V–Packings
NOTE:
There
are two types of packing kits:
one is just
packings, the other includes the packings,
rings
and retainers.
1. Remove the manifold as outlined in the Pumping
Section.
2. Carefully pull the packing retainer from the
manifold.
Examine the o–ring and replace it if it is cut
or
damaged.
3. Remove the v–packing and head ring. Pull out the
intermediate retainer ring. Remove the second
v–packing
and second head ring.
4.
Inspect all parts and replace as necessary
.
5. Thoroughly
clean the packing cavities and examine.
6. Lightly
grease the packing cavities and then replace
the packings in the following order: head ring,
v–packing,
intermediate ring,
head ring, v–packing
and
packing retainer with the o–ring installed in
the
retainer
groove.
CAUTION
Be
very sure the parts are installed in the proper
order and facing the correct direction. See
Pump assembly on pages 18 and 20.
Improperly installed parts will cause a
malfunction.
7. Reassemble
the
manifold as instructed in Servicing
the
Plungers.
ACCESSORIES
(Must be purchased separately)
DOWNSTREAM CHEMICAL INJECT
OR KIT
(1535) 800–139
DOWNSTREAM CHEMICAL INJECT
OR KIT
(2040) 800–111
For injecting harsh cleaning chemicals downstream
from
the pump.
UPSTREAM CHEMICAL INJECTOR KIT
800–257
For
injecting mild
cleaning chemicals upstream into the
pump.
BACKFLOW
PREVENT
OR 801–133
Prevent back–up of contaminated water into fresh
supply.
Install upstream of pump.
ANTI–FREEZE FLUSH KIT 802–327
For
flushing system with 50% anti–freeze solution prior
to transporting or storing pressure washer in below
freezing
temperatures.
INLET
PRESSURE REGULA
TOR 800–258
Regulates inlet water pressure to 60 psi (4 bar)
maximum.
TECHNICAL DATA
Model
800–290
Model 800–164Model 800–367Model 800–165
Engine
(air–cooled, 4 cycle)
Gasoline T
ank Capacity
W
ater Pump Maximum
Working Pressure
W
ater Pump Maximum Flow
Inlet Hose Connection
Weight
Dimensions
Length
Width
Height
Maximum Inlet W
ater
Temperature
W
etted Parts
High Pressure Hose
Bypass Hose
Pressure Washer
(including fittings)
5 hp Honda OHV
5 hp Briggs &
8 hp Briggs &
8 hp Honda OHV
Stratton I/C Stratton I/C
3.8 quarts (3.6 liter)
3 quarts (2.8 liter) 6 quarts (5.7 liter) 6.2 quarts (6 liter)
1500 psi (103 bar) 1500 psi (103 bar) 2000 psi (138 bar) 2000 psi (138 bar)
3.5 gpm (13 lpm) 3.5 gpm (13 lpm) 4 gpm (15 lpm) 4 gpm (15 lpm)
3/4” garden hose (f) 3/4” garden hose (f) 3/4” garden hose (f) 3/4” garden hose (f)
105 lb (48 kg) 105 lb (48 kg) 152 lb (68 kg) 158 lb (70 kg)
37” (940 mm) 37” (940 mm) 36” (914 mm) 36” (914 mm)
19” (483 mm) 19” (483 mm) 21” (533 mm) 21” (533 mm)
20” (508 mm) 20” (508 mm)
22.5” (572 mm) 22.5” (572 mm)
160_ F
(70
_ C) 160_ F
(70
_ C) 160_ F
(70
_ C) 160_ F
(70
_ C)
Acrylonitrile
and Buna–N cover and tube
Synthetic yarn and EPDM
Anodized aluminum, Aluminum or bronze alloys, Brass Copper
, Nylon–
r
composite,
Ceramic, Buna–N, Cotton phenolic, 303, 304, and 316 Stainless steel, Polymide–12
thermoplastic,
r
, Carbon steel, Zinc with or without yellow chromate plate
is a registered trademark of the DuPont Company
.
PTFE
PTFE
PTFE
PTFE
PTFE
PTFE
PTFE