Filter
Top Products
9
374-7-99
10 11 12
To Use Your Changing Table
(on certain models)
Parts List
CHECK that you have all parts listed below
BEFORE assembling your changing table.
No tools required.
Long tube (2)
Short tube (2)
Changing pad
Accessory bag
Changing
table
Step 1.
Lay changing table flat on floor with short side in front
of you and belt facing up. Gently slide one long tube into
opening on long side exactly as shown.
Repeat on other side.
Step 2.
Slide one short tube
into opening on end
as shown.
For proper orientation,
be sure folding side of
hinge faces pad as
shown.
DO NOT insert
other short tube
at this time.
Fold side
of hinge
Long
side
Short side
Step 3.
Turn up long tube so
that its end points down.
Insert end of long tube
into opening on end of
short tube as shown.
DO NOT slide short
tube up around the bend
of long tube until you
have finished next step.
Make sure fabric does
not get caught in
opening when inserting
long tube into short tube.
Step 4.
Repeat step 3 on other
end of short tube, then
slide short tube ends up
onto long tubes.
TO AVOID TEARING
FABRIC, slide this end
up before proceeding
with step 4.
Step 5.
Repeat steps 2
and 3 on other end
of changing table.
If the short tubes have
been inserted correctly,
the changing table
should be able to
FOLD UP in the
center as shown. If you
cannot fold the tubes
up in the center, review
steps 2, 3, and 4.
Step 6.
Place pad in changing
table with vinyl side up.
Pull belt straps through
holes in center of pad.
Step 7.
Insert VELCRO
®
straps
into the four slots at the
corners of changing table
and attach to VELCRO
®
on underside of changing
table. This will prevent
pad from moving.
Step 8.
Place changing table on
Pack N Play as shown.
You may use your changing
table with or without your
bassinet installed. Make
sure tubes are securely
over the sides of the
Pack N Play.
Check that the changing
table is supported
by the Pack N Play by
pushing firmly down into
center of changing table.
Short tube side
Slide ends up
To Use Accessory Bag
If your bassinet is already installed, unsnap the four
snaps on the bassinet end flap from either end of
Pack N Play.
Step 1.
Snap accessory bag
onto end of Pack N
Play with four snaps
as shown.
Step 2.
Snap bassinet end flap
over the accessory bag
with the four snaps.
To Fold Changing Table
Step 1.
Pull up on waist belt
straps to fold.
Step 2.
Ends of long tubes
must point up when
folded as shown.
Fold up
Ends of tubes
point up
To protect your child from falls and
other injuries:
Always stay within arms reach of your child when
using the changing table. Always use waist belt
when child is on the changing table. Never leave
child unattended.
The changing table is designed for use only with
this Graco Pack N Play. Do not attempt to use it
with any other product. Before each use, make
sure the changing table is properly secured to
the Pack N Play by pushing down firmly in the
middle of the changing table. The changing table
should not fall.
Do not use the changing table as a sleeping or
play area.
Weight limit for the changing table is 25 pounds
(11.3 kg). Do not use the changing table as extra
storage. Always remove the changing table when
your child is in the Pack N Play.
The Pack N Play changing table can be used on
the floor without being attached to the Pack N
Play. Never place the changing table on a piece of
furniture, bed, counter or any raised surface from
which the changing table or your child could fall.
Step 3.
To carry or store your changing table
with your folded Pack N Play, see
To Cover Your Pack N Play section
in these instructions.