Filter
Top Products
9
133-9-00 IS2492
10 1211
Using the Tray
Step 1.
Unlatch the tray by squeezing
the two latches under the tray at
the same time, and lift up.
Be careful not to let the tray
hit your baby when lifting or
closing the tray.
Step 2.
To latch tray, push it down firmly.
If tray does not latch, check back brace to be sure the word
REAR is away from the seat.
Step 1.
Slide the pocket of the seat
cover over the top of the seat
as shown.
Step 2.
Pull crotch strap and both
ends of the seat belt through the
slots in the seat cover.
Step 3.
Push the elastic loop through
the hole on one side of seat.
Step 4.
Fold cover around bottom of
seat. Then fasten the hook into
the elastic loop on one side as
shown. Repeat on other side.
CAUTION: Be sure the seat
cover at armrest does not
interfere with tray latching.
Attaching the Seat Belt
Step 1.
Thread one end of the
seat belt through the belt
retainer as shown.
Step 2.
Thread both ends of seat belt
through the buckles as shown.
CHECK that the belt is threaded
correctly by pulling on the seat
belt. The belt should not slip
through the buckle.
To release, push in on
front of buckle.
Reclining Back
Four Positions
Pull adjustment wire upward
and pull seat backward to
recline seat. Extra pressure is
required to go from the third
position to full recline.
For upright position, simply lift
back of seat forward.
Tray must be latched at all times when
baby is in swing. Pull up on tray to be sure it is latched.
Attaching the Seat Cover
Step 3.
To replace lid, put the two
tabs of the lid into the two
slots in the bottom of the motor
housing. Swing lid up, and
press it into place until you
hear the latch click.
Coin
slot
Installing the Batteries
Indicator Light-
Red light comes on
when swing is turned on.
Step 1.
With baby out of swing, open
the battery compartment lid by
inserting a coin (penny, nickel or
dime) into the coin slot. After the
lid pops open, swing it down and
remove it.
Step 2.
Insert four D cells. CHECK that
the batteries are put in correctly.
Your swing will not run if the
batteries are put in backwards.
Step 2.
Place crotch strap between
childs legs and snap both side
buckles to the center buckle.
Adjust belt as needed to get
a snug fit around your child.
Step 3.
Close the tray. CHECK that the tray
is latched by pulling up on the tray.
Step 4.
To start swing, slide the speed
button to the desired speed and
give the swing a gentle push.
Observe the swinging motion for
a minute. It takes time for the
swing to adjust to a setting.
Change setting if needed.
A small, quiet baby will swing higher on each setting
than a larger, more active baby.
Step 5.
To turn swing off, slide switch to
the center OFF position.
Do not depend on
the tray or seat belt alone to hold
your baby. Always secure your
baby with both the seat belt and
tray when your baby is in the
swing.
Toy Mounting System
Your swing has a toy mounting system in the tray. This
swing model does not come equipped with toys. If you
would like to order toys, please see the enclosed leaflet
for information. Please insert the two plastic covers as
described below to fill the holes in the tray.
To Install Covers
To insert a cover into the tray of
your swing, first push one side into
a notch, then push in the other side.
Your seat may be stopped at any time the motor is
running without damaging the motor. Push swing
to restart.
If your swing motor stops operating by itself, a
protective device may have been activated. Turn
off motor, wait three minutes, then restart swing.
Starting the Swing
CHECK that all parts are securely fastened together
before using the swing.
Step 1.
Open tray and seat belt. Place baby in the seat.
(If your child is very small, you may want to use
rolled-up blankets as a prop.)