Filter
Top Products
f) If operating a power tool in a damp location is
unavoidable, use a residual current device
(RCD) protected supply.
Use of an RCD
reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication.
A moment of inattention while
operating power tools may result in serious
personal injury.
b) Use personal protective equipment. Always
wear eye protection.
Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
Obtainable from a
workwear supplier.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool.
Carrying power tools
with your finger on the switch or energising power
tools that have the switch on invites accidents.
d) Do not overreach. Keep proper footing and
balance at all times.
This enables better control
of the power tool in unexpected situations.
e) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts.
Loose clothes,
jewellery or long hair can be caught in moving
parts.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application.
The correct
power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off.
Any power tool that
cannot be controlled with the switch is dangerous
and must be repaired.
c) Disconnect the plug from the power source
before making any adjustments, changing
accessories, or storing power tools.
Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool.
Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition that
may affect the power tool’s operation. If
damaged, have the power tool repaired before
use.
Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean.
Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed.
Use of the
power tool for operations different from those
intended could result in a hazardous situation.
5. Service
a) Have your power tool serviced by a qualified
repair person using only identical
replacement parts.
This will ensure that the
safety of the power tool is maintained.
Chain saw safety warnings:
• Keep all parts of the body away from the saw
chain when the chain saw is operating.
Before you start the chain saw, make sure the
saw chain is not contacting anything.
A
moment of inattention while operating chain saws
may cause entanglement of your clothing or body
with the saw chain.
• Always hold the chain saw with your right
hand on the rear handle and your left hand on
the front handle.
Holding the chain saw with a
reversed hand configuration increases the risk of
personal injury and should never be done.
• Wear safety glasses and hearing protection.
Further protective equipment for head, hands,
legs and feet is recommended.
Adequate
protective clothing will reduce personal injury by
flying debris or accidental contact with the saw
chain.
Obtainable from a workwear supplier.
• Do not operate a chain saw in a tree.
Operation of chain saw while up a tree may result
in personal injury.
• Always keep proper footing and operate the
chain saw only when standing on fixed,
secure and level surface.
Slippery or unstable
surfaces such as ladders may cause a loss of
balance or control of the chain saw.
• When cutting a limb that is under tension be
alert for spring back.
When the tension in the
wood fibres is released the spring loaded limb
may strike the operator and/or throw the chain
saw out of control.
• Use extreme caution when cutting brush and
saplings.
The slender material may catch the
saw chain and be whipped forward toward you or
pull you off balance.
• Carry the chain saw by the front handle with the
chain saw switched off and away from your
body. When transporting or storing the chain
saw always fit the guide bar cover.
Proper
handling of the chain saw will reduce the likelihood
of accidental contact with the moving saw chain.
• Follow instructions for lubricating, chain
tensioning and changing accessories.
Improperly tensioned or lubricated chain may
either break or increase the chance for kickback.
• Keep handles dry, clean and free from oil and
grease.
Greasy, oily handles are slippery
causing loss of control.
• Cut wood only. Do not use chain saw for
purposes not intended. For example: do not
use chain saw for cutting plastic, masonry or
non-wood building materials.
Use of the chain
saw for operations different than intended could
result in a hazardous situation.
ENGLISH - 3