Filter
Top Products
Starting and Stopping
To Start your Lawnmower
1. Move the handle to the parking position (C2).
2. Connect the spark plug lead. (J).
3. Open the fuel tap (K).
4. Move the Choke control lever to the ‘Choke’
position (L) when starting from cold, and to the
‘Run’ position (N) when starting from hot.
5. Pull and firmly hold the Operator Presence
Control to the upper handle.
6. Place your right foot firmly on the deck and grasp the
top of the lower handle with your left hand. Tilt the
trimmer towards you (M). This ensures the product
is in a secure position when starting and also
prevents an unsightly ring being cut in your lawn.
7. Pull the starting handle gently until you feel a
resistance, return the starting handle slowly.
8. Pull the starting handle firmly towards you to its
full extent.
9. Allow the engine to reach its full running speed
then gently lower the lawnmower to the ground.
10.When the engine has warmed up make sure the
choke control lever is in the 'Run' (N) position.
To Stop your Lawnmower
• Blade continues to rotate after the machine has
switched off, rotating blades can cause injury.
1. Release the Operator Presence Control.
2. As the engine dies, tilt the lawnmower slightly.
This prevents a ring being cut in your lawn.
3. When the engine has stopped, lower the
lawnmower to the ground.
4. Put the handle in the Parking position (C2).
5. Close the fuel tap (K)
Adjusting the cutting height
Adjusting the Cutting Height
• Never use more than 2 cutting height spacers.
• Spacers can only be fitted between the blade
and the fan and never between blade and the
bolt (P).
1. Ensure the Operator Presence Control is
released, when the engine has stopped rotating
- disconnect the spark plug lead.
2. Close the fuel tap (K). Turn your lawnmower on its side.
3. Remove the blade bolt (P1) and blade (P2) as
described in ‘Removing the Blade and Fan’.
4. For a Lower Cut - Add spacers (P3) to a
maximum of 2.
5. For a Higher Cut - Take spacers (P3) away.
6. Refit the blade as described in ‘Fitting the
Blade and Fan’.
How to Mow
1. Place the handle in the mowing position (C3).
2. Mow twice a week in the growing season. Your
lawn will suffer if more than one third of its
length is cut at one time.
• Keep hands and feet away from the blade, a
rotating blade cannot be seen.
• Mowing on banks and slopes can be
dangerous. Do not mow on steep slopes.
• Always keep your feet on flat ground with the
mower below you on the slope and with the
spark plug uppermost to avoid lubricating oil
running into the cylinder.
• Do not use this mower on slopes which are
wet or more than 45
0
from horizontal.
• Never push the mower up the slope.
Removing & Fitting the Blade & Fan
Oil
Use 4-stroke automotive detergent oil. SAE
10W-30 is recommended for general use.
Fill with oil as instructed in your Engine Owners
Manual provided with your product.
AIR CLEANER
TIP
THIS
WAY
ONLY
Before any servicing to the
underside of your machine, close
the fuel tap, let the engine run
until it stops, disconnect the
spark plug lead and TIP THE
MACHINE ON ITS SIDE WITH
THE AIR CLEANER UPPERMOST.
IMPORTANT
WARNING
• Always handle the blade with care - sharp
edges could cause injury. USE GLOVES
• Spark plug lead may be hot - handle with
care.
Removing the Blade and Fan
• Renew your metal blade after 50 hours
mowing or 2 years whichever is the sooner -
regardless of condition.
• If the blade is cracked or damaged replace it
with a new one.
1. Ensure the Operator Presence Control is released,
when the engine has stopped and the blade has
stopped rotating - disconnect the spark plug lead.
2. Fully close the fuel tap (K).
3. Turn your lawnmower on its side with the air
cleaner uppermost (see pic above).
4. To remove the blade bolt (P1), hold the fan (P4)
firmly and with the spanner provided loosen the
blade bolt by turning it anti-clockwise.
5. Remove the blade bolt (P1), blade (P2), spacers
(P3) and fan (P4).
6. Inspect for damage and clean as necessary.
ENGLISH - 3