Filter
Top Products
OPERATING INSTRUCTIONS
Assembly Instructions
Warning: Remove the plug
from the power source before
assembly of leaf blower. This will
help prevent accidental starting of
the unit which could result in serious
injury.
6
Caution: The impeller rotates for
a few seconds after you turn off the
blower and will cause injury. WAIT until all
parts stop moving.
Note: Instructions must be followed in
order.
1. Remove all parts from the packaging.
2. Remove the nuts and screws
provided from the packaging.
3. Insert the blower/vacuum tube all the
way into the opening on the motor
housing until the holes in the tabs on
the blower/vacuum tube align with
the screw holes in the housing. (Fig. 1)
2. Slide the vacuum bag over the debris
exhaust tube on the housing. (Fig. 2)
Motor Housing
Blower/Vacuum
Tube
Nut
Self-Tapping
Screw
Screw
Screw
Self-Tapping
Screw
Nut
Fig. 1
Air Intake
(Vacuum)
Air Output
(Blower)
Fig. 2
4. Insert the two (2) screws into the
right side of the motor housing the
two (2) nuts into the left side of the
motor housing. (Fig. 1)
5. Tighten the screws firmly. Do NOT
over-tighten.
6. Insert the two (2) self-tapping screws
into the holes on either side of the
blower outlet housing. (Fig. 2 )
7. Tighten the screws firmly but do
NOT over-tighten.
Note: If it is necessary to disassemble
the leaf blower, follow these instructions:
8. Turn the unit “Off” and remove the
plug from the extension cord.
9. Remove the two (2) self tapping
screws from either side of the blower
outlet housing.
10. Remove the two (2) screws and nuts
holding the blower/vacuum tube to
the housing.
Note: Place the all the screws and nuts
in a safe place for future use.
11. Remove the blower/vacuum tube
from the motor housing.
Important: Always replace the
blower/vacuum tube before using the leaf
blower.
Attaching the Vacuum Bag
Vacuum Bag Hook
Buckle
Fig. 3
Debris Exhaust
Tube
Important: The leaf blower will not run
unless the vacuum tube is locked in
place.
Warning: Remove the plug
from the power source before
assembly of leaf blower. This will
help prevent accidental starting of
the unit which could result in serious
injury.
1. Slide the buckle that is on the
vacuum bag onto the vacuum
bag hook that is on the
underside of the blower/vacuum
tube. (Fig. 3)
Fig. 4
OPERATING INSTRUCTIONS
3. Tighten the vacuum bag onto the
debris exhaust tube and fasten the
velcro strap securely on top of the
ridge created for the bag cuff. (Fig. 4)
Debris Exhaust
Tube
Vacuum Bag
4. To remove the vacuum bag, loosen
the velcro strap and pull the vacuum
bag off of the debris exhaust tube.
(Fig. 5)
Fig. 5
5. Always replace the vacuum bag
before using the leaf blower.
Pull vacuum
bag down
Attaching the Shoulder Strap
If the shoulder strap is not already put
together:
1. Push the end through the center of
the buckle.
2. Pull the strap over the cross bar and
down through the slot in the buckle.
(Fig. 6)
Fig. 6
3. Fully extend the shoulder strap.
(Fig. 7)
Clip
Fig. 7
4. Attach the metal clip of the shoulder
strap to the latch support on top of the
handle. (Fig. 8)
Latch Support
Clip
Fig. 8
5. Place the shoulder
strap over your
head and opposite
shoulder. (Fig. 9)
6. While in the
operating position,
adjust the length
of the shoulder
strap to fit your
height. To lengthen
the shoulder strap,
pull the strap down
and move he buckle
up. To shorten, pull
the strap back through the buckle
while moving the buckle down.
(Fig. 10)
Fig. 9
Fig. 10
To Lengthen
To Shorten
7