Filter
Top Products
Program icon
:
The "Program" icon lights up when Programming.
Progress bar
:
A visual indication of the time remaining before an
equipment is turned off or before the end of the standby mode.
Progress bar
equipment is turned off or before the end of the standby mode.
Progress bar
A visual indication of the time remaining before an
equipment is turned off or before the end of the standby mode.
A visual indication of the time remaining before an
Set Point icon
:
The "Set Point" icon automatically turns on when
set point setting menu is activated. (SP message on display).
The "Set Point" icon automatically turns on when
set point setting menu is activated. (SP message on display).
The "Set Point" icon automatically turns on when
It fl ashes when:
set point setting menu is activated. (SP message on display).
It fl ashes when:
set point setting menu is activated. (SP message on display).
1- there is a call for heat and heater has not started yet,
2- heater has just turned off and element is cooling down or
1- there is a call for heat and heater has not started yet,
2- heater has just turned off and element is cooling down or
1- there is a call for heat and heater has not started yet,
3- if system is performing a check fl ow.
2- heater has just turned off and element is cooling down or
3- if system is performing a check fl ow.
2- heater has just turned off and element is cooling down or
Service icon
:
A problem has been detected.
Do not enter the water! Spa service is required.
A problem has been detected.
Do not enter the water! Spa service is required.
A problem has been detected.
9919-100
xxx
Cooldown
While performing these tasks,
the heater is not allowed to turn
on and its icon fl ashes. The heater
is not allowed also to come on
throughout the cool down period
of the heater element.
Water temperature regulation
In a regulation cycle, the system fi rst
generates water fl ow through the
heater housing and the plumbing,
in order to ensure accurate water
temperature readings as well as
avoiding heater activation in dry
conditions.
After verifying pump activation and
taking a water temperature reading
if required, the system automatically
turns the heater on to reach and
maintain water temperature at
Set Point.
Setting temperature unit
Water temperature can be displayed
in either Fahrenheit (˚F) or Celsius (˚C).
• Press
Ok
key a
Ok key a Ok
eighth
time.
• The display will show either
˚F or ˚C.
• Use (
+
)
or (
-
)
key to change setting.
• Press
Ok
key a last time to go back
Ok key a last time to go back Ok
to normal mode.
Program key
Use
Program
key to display time
or enter Programming menu by
pressing and holding key.
In Programming mode,
the following parameters can be
set:
time, fi lter cycle’s start time,
duration, frequency,
and the choice
of temperature display units.
Setting the time
Enter Programming mode by
holding
Prog
. key pressed down
for 3 sec. The display will show the
current time setting.
Setting the hour
:
Use (
+
)
or (
-
)
key to change hour
setting (
AM/PM
).
Setting the minutes
:
Press
Ok
key.
Ok key.Ok
Use (
+
)
or (
-
)
key to change
minutes setting.
F
ilter
cycle frequency
ilter cycle frequencyilter
Press
Ok
key a fourth time.
Ok key a fourth time.Ok
The display will show
FFxx
, with "xx"
representing the number of fi lter
cycles per day (up to 4).
Use (
+
)
or (
-
)
key to change setting.
Setting fi lter cycle start time
To program the fi lter cycle, you
must enter these parameters: the
start time, duration and frequency.
During a fi lter cycle, pumps run for
one minute to purge the plumbing,
then Pump 1 low speed runs for the
programmed number of hours.
Press
Ok
key a second time.
Ok key a second time.Ok
The display will show
F
Sxx
, with "xx"
representing the starting hour.
Use (
+
)
or (
-
)
key to change setting
(01:00- 12:00 AM/PM).
Programming
Light icon
:
The "Light" icon lights up when the light is on.
Pumps icons
:
The "Pump" indicator numbers light up and their
icons become animated when pumps are on.
Pumps icons
icons become animated when pumps are on.
Pumps icons
The "Pump" indicator numbers light up and their
icons become animated when pumps are on.
The "Pump" indicator numbers light up and their
Smart winter mode icon
:
The "SWM" icon automatically turns
on when freeze protection is active. It fl ashes while system
The "SWM" icon automatically turns
on when freeze protection is active. It fl ashes while system
The "SWM" icon automatically turns
purges the spa plumbing.
on when freeze protection is active. It fl ashes while system
purges the spa plumbing.
on when freeze protection is active. It fl ashes while system
Filter Cycle icon
:
The "Filter Cycle" icon lights up when fi lter cycle
is on. It fl ashes when fi ltering is suspended.
Filter Cycle icon
is on. It fl ashes when fi ltering is suspended.
Filter Cycle icon
The "Filter Cycle" icon lights up when fi lter cycle
is on. It fl ashes when fi ltering is suspended.
The "Filter Cycle" icon lights up when fi lter cycle
Heater icon
:
The "Heater" icon lights up when the heater is on.
Blower icon:
The “Blower”
icon
lights up
when blower is on.
I
con Description
Setting fi lter cycle duration
Press
Ok
key a third time.
Ok key a third time.Ok
The display will show
Fdxx
, with “xx”
representing the duration in hours.
Use (+) or (-) key to change setting
(0-12 hours).
Other features
Setting Economy mode
The Economy mode allows you to
lower the temperature set point
of the spa by 20 °F (11 °C) during a
certain period of the day.
•
Press
Ok
key a fi fth time.
Ok key a fi fth time.Ok
•
Use (+) key to enable the economy
mode, the display will show EP 1.
•
Use (-) key to disable economy
mode, the display will show EP 0.
Setting Economy start time
To program the Economy mode, you
must enter two parameters: the start
time and the duration.
•
Press
Ok
key
Ok keyOk
a sixth time.
key a sixth time. key
•
The display will show
ESxx
, with
“xx” representing the starting hour.
•
Use (+) or (-) key to change setting
(0:00 h - 23:00h).
Setting Economy duration
•
Press
Ok
key
Ok keyOk
an seventh time.
key an seventh time. key
•
The display will show
Edxx
, with
“xx” representing the duration
in hours.
•
Use (+) or (-) key to change setting.
If the Economy mode is not re-
quired the duration must be set to
“0”. If continuous activation of the
Economy mode is required the
duration must be set to “24”.
Setting Economy duration
When in Economy mode, the “Econ”
message is displayed.
Smart Winter Mode
Our Smart Winter Mode protects
your system from the cold by turn-
ing pumps on several times a day to
prevent water from freezing in pipes.
www.geckoalliance.c
om