Filter
Top Products
Rate Chart for Impregnating Fertilizer with DuPont™
VELPAR® L
Fertilizer VELPAR® L Rate Per Acre
Rate/Acre 2 Pints 3 Pints 4 Pints 6 Pints
250 pounds 16 pts/ton 24 pts/ton 32 pts/ton 48 pts/ton
300 pounds 13.4 pts/ton 20 pts/ton 26.8 pts/ton 40.2 pts/ton
350 pounds 11.4 pts/ton 17.2 pts/ton 22.8 pts/ton 34.2 pts/ton
400 pounds 10 pts/ton 15 pts/ton 20 pts/ton 30 pts/ton
450 pounds 8.8 pts/ton 13.2 pts/ton 17.6 pts/ton 26.4 pts/ton
For rates other than those listed, use the following formula to
calculate the amounts of VELPAR® L to be impregnated per
ton of dry fertilizer.
Pints Pints
VELPAR® L X
2000
= VELPAR® L Per
Per acre
Lbs Fertilizer Per Acre
Ton of Fertilizer
APPLICATION
Uniform application of VELPAR® L-impregnated dry
fertilizer is essential for satisfactory weed control. Accurate
calibration of the application equipment is essential for
uniform distribution to the surface. The recommended
method of application is to apply 1/2 the recommended rate
and overlap 50%. This results in the best distribution
pattern.
USE PRECAUTIONS - ALFALFA
• Best results are obtained when 1/2–1 inch of rainfall or
sprinkler irrigation occurs within two weeks after
application, when soil is moist at time of application, and
when weeds have not germinated or are less than 2 inches
in height or diameter. Heavy rainfall or excessive irrigation
after application may result in crop injury or poor
performance of the herbicide.
•
On soils high in organic matter (greater than 5%), the
effectiveness of VELPAR® L can be significantly reduced
and weed control may be unsatisfactory.
•
Crop injury, including mortality, may result in fields with
r
estr
icted root growth due to nonuniform soil profiles
such as gr
a
v
el bases and clay lenses.
•
Crop injury may result if hot weather, mid-to-high 90
degree range or higher, occurs within a few days after
application.
•
Do not apply to snow-covered or frozen ground.
•
Since the ef
f
ect of VELPAR® L on alfalfa varies with soil
conditions,
unif
or
mity of a
pplication, and environmental
conditions, growers should limit their first use to small
areas.
• If abnormally dry conditions exist following application,
restrict the first irrigation to no more than 1/2 acre inch of
water.
• Temporary yellowing of alfalfa may occur following
VELPAR® L applications.
• Treat only stands of alfalfa established for one year or for
one growing season (e
xcept in California), provided:
–The alfalfa stand has a well developed tap root structure
that is at least 10 inches in length (0.25 inch diameter
below the crown) throughout the field and the crop is
healthy, vigorous, and not under stress from weather
c
onditions, low fertility, insects or disease damage.
–
In areas with shorter growing seasons, such as, higher
elevations, adequate alfalfa tap root growth may not occur
a
nd especially when alfalfa is grown together with a cover
or nurse crop. If an adequate tap root is not present, delay
application of VELPAR® L until the alfalfa has gone
through a minimum of two growing seasons.
• In California, fall planted alfalfa may be treated in the
following winter months with VELPAR® L at 1 to 2 pints
per acre (use higher rate for fine textured soils) provided:
- alfalfa root growth exceeds 6 inches in length
- vegetative top growth of alfalfa has lateral development of
secondary growth
- alfalfa is healthy and vigorous, not growing under stress
from insect, disease, winter injury or other types of stress.
Injury may result to alfalfa plants that fail to meet these
g
rowth criterion listed above.
•
Do not use VELPAR® L on seedling alfalfa, alfalfa-grass
mixtures, or other mixed stands as injury may result to the
seedling alfalfa or companion crop.
• Do not add a surfactant to VELPAR® L when treating non-
dormant alfalfa.
• Do not use VELPAR® L on gravelly or rocky soils,
exposed subsoils, hardpan, sand, poorly drained soil, or
alkali soils.
SEED ALFALFA (CALIFORNIA ONLY)
ADDITIONAL USE PRECAUTIONS
• Do not use VELPAR® L on fields with sandy loam or
loamy sand soils having less than 1% organic matter.
• Do not exceed 2 pints per acre on fields with sandy loam or
loamy sand soils having 1–2% organic matter.
• Do not exceed 2 pints per acre on seed alfalfa that has been
established for only one growing season.
HIGH BUSH BLUEBERRIES
VELPAR® L is recommended for control of certain
herbaceous and woody weeds in established high bush
blueberry fields.
APPLICA
TION INFORMATION
VELPAR® L may be applied to high bush blueberries that
have been established for 3 or more years. Apply
VELP
AR®
L in the spring before blueberry leaf emergence.
Direct the spray solution towards the soil and weeds.
Using calibr
ated ground spray equipment, make the
application in sufficient water to provide thorough and
uniform coverage to the treated area (usually 20 gallons per
acre). Shut off spray booms when starting, turning, slowing
or stopping, or injury to the crop may result.
BLUEBERRY
7