Filter
Top Products
u =, in u l
STORAGE
Prepare your chipper-shredder for' storage at the end
of the season or if the unit will not be used for 30 days
or more,,
WARNING: NEVER STORE MACHINE
WITH FUEL IN THE FUEL TANK INSIDE
OF BUILDING WHERE FUMES MAY
REACH AN OPEN FLAME OR SPARK, OR
WHERE IGNITION SOURCES ARE
PRESENT SUCH AS HOT WATER AND
SPACE HEATERS, FURNACES, CLOTHES
DRYERS, STOVES, ELECTRIC MOTORS,
ETC.
NOTE: A yearly check-up by your local Sears Service
Center is a good way to make certain your chipper-
shredder will provide maximum performance for the
next season,
CHIPPER-SHREDDER
e Clean the chipper-shredder thoroughly,
e Wipe unit with an oiled rag to prevent rust (use a
light oil or siticone),.
ENGINE
IMPORTANT: IT IS IMPORTANT TO PREVENT
GUM DEPOSITS FROM FORMING IN ESSENTIAL
FUEL SYSTEM PARTS SUCH AS CARBURETOR,
FUEL FILTER, FUEL HOSE, OR TANK DURING
STORAGE,. ALSO, EXPERIENCE INDICATES THAT
ALCOHOL BLENDED FUELS (CALLED GASOHOL
OR USING ETHANOL OR METHANOL) CAN
ATTRACT MOISTURE WHICH LEADS TO SEPARA-
TION AND FORMATION OF ACIDS DURING STOR-
AGE ACIDIC GAS CAN DAMAGE THE FUEL SYS-
TEM OF AN ENGINE WHILE IN STORAGE
e Drain the fuel tank,
® Start the engine and let it run until the fuel lines and
carburetor are empty
e Never use engine or carburetor cleaner products in
the fuel tank or permanent damage may occur,
e Use fresh fuel next season
NOTE: Fuel stabilizer is an acceptable alternative in
minimizing the formation of fuel gum deposits during
storage, Add stabilizer to gasoline in fuel tank or stor-
age container, Always follow the mix ratio found on
stabilizer container,, Run engine at least 10 minutes
after adding stabilizer to allow the stabilizer to reach
the carburetor Do not drain the gas tank and carbure-
tor' if using fuel stabilizer,,
e Drain all the oil from the crankcase (this should be
done after the engine has been operated and is still
warm) and refitl the crankcase with fresh oil
e If you have drained the fuel tank, protect the inside
of the engine as follow& Remove spark plug, pour
approximately 1/2 ounce (approximately one table-
spoon) of engine oil into cylinder and crank slowly
to distribute oil_ Replace spark plug,
OTHER
e Do not store gasoline from one season to another,
e Replace your gasoline can if your can starts to rust.
Rust and/or dirt in your gasoline will cause problems,,
e Store unit in a clean, dry area, Do not store next to
corrosive materials, such as fertilizer.
NOTE: If storing in an unventilated or metal storage
shed, be certain to rustproof the equipment by coating
with a light oil or silicone,
SERVnCE & ADJUSTMENT
i ...... i,,=,,H
WARNING: ALWAYS STOP ENGINE AND
DISCONNECT SPARK PLUG WIRE AND
MOVE IT AWAY FROM SPARK PLUG
BEFORE PERFORMING ANY ADJUST-
MENTS OR REPAIRS.
REMOVINGTHE FLAIL SCREEN
If the discharge area becomes clogged, remove the
flaiI screen and clean area as follow&
e Stop the engine, make certain the chipper-shredder
has come to a complete stop and disconnect spark
plug wire from the spark plug before unclogging the
chute,
e Loosen the two hand knobs on each side of the
chute deflector. Lift the chute deflector up, and tie it
out of the way.
® Remove two hairpin clips from the clevis pins which
extend through the housing, Remove the clevis
pins. Lift the flail screen from inside the housing_
See figure 18,
e Clean the screen by scraping or washing with
water, Reinstall the screen,,
NOTE: Be certain to reassemble the flail screen with
the curved side down as shown in figure 18
13