Filter
Top Products
Controlling the SM-150X
1. FC-4HS Timer remote - Plug the controller into the back of the SM-150X and press the red button to
continually generating snow. Press the yellow button to activate the timer functions. Adjust the duration and
interval knobs to achieve the desired effect. The unit will cycle regularly to the settings. Depress the yellow
button again to exit time mode. To use the FC-4HS manually, simply depress and hold the green button to
generate the desired amount of snow.
2. DMX Mode - The SM-150X is a one channel unit that controls the volume of snow generated. To operate
in DMX mode, you must link the units together using a premium quality 3-pin DMX cable in the following
configuration. 'Out' from the first unit to 'In' on the second, 'Out' from the second to 'In' on the third and so
on. Please consult the controller manual to determine the proper address for the units.
Example: To set the address at 12
Installation / Mounting
The snow machine must be used in a horizontal position sitting on a level surface or it may be mounted
using the bracket provided. Ensuring that the snow is not shooting directly at anyone's face. Whatever
method of installation you choose, the snow machine must not have more than a 15 degree angle of incli-
nation. We always suggest that for safety purposes use of a suitable hanging clamp and safety cable is
essential. CHAUVET offers a range of items, which are ideal for safe mounting.
Replacing Fuses
If the unit does not function at all when connected to the main power supply then it is highly likely that the
fuse has blown.
Disconnect from main power supply before attempting to replace the fuse.
In order to replace the fuse, disconnect from the main power supply first, and then remove the fuseholder
cover to reveal the fuse. The unit has a label attached which indicates the correct fuse rating and you will
also find this listed as part of the specifications for the unit later in this guide. It is most important that
replacement fuses are of the correct rating. Failure to use the correct fuse could damage the unit beyond
economic repair.
The fuse should simply be placed inside the holder and the cover replaced. When this is done connect to
the main power supply to check. If the unit is still not working then please contact CHAUVET.
Cleaning
Cleaning your snow machine regularly will help reduce costly parts replacement and repair charges.
After every 20 hours of continuous operation or when the machine will be idle for a long time it is recom-
mended to run a cleaning solution composed of 80% distilled water and 20% white vinegar through the
system to prevent the accumulation of particles in the pump and tubing.
1. While unit is unplugged, remove the sock front of unit (fig.1) and clean out debris
with white vinegar and a pipe cleaner, making sure that the hole is free and unobstructed.
2. Empty all snow fluid from the machine and replace with cleaning solution in the tank.
Plug unit in.
3. Run unit in a well ventilated area until tank is empty.
4. Replace the sock.
5. Cleaning is now complete. Unplug and refill with a quality water based snow fluid once cool.
All snow machines are prone to clogging due to the consistency of the fluid. However a well maintained
machine should provide years of reliable use. The body of the unit may be cleaned with a dry cloth. Store
dry.
Introduction
Congratulations on the purchase of your new CHAUVET snow machine. We are confident you will enjoy
many trouble free hours with this unit. To assist with the care and use of the product we have prepared this
short guide.
Operation
Before connecting this unit to the mains power supply for the first time you must first fill the fluid tank with
snow fluid. Place the machine on a level surface and loosen the cap of the fluid tank to fill with quality
unscented water based snow fluid. We recommend use of CHAUVET snow fluid as it has been specially
formulated for use with CHAUVET snow machines. Plug the remote control unit into the socket at the rear
of unit. The snow machine is ready to work immediately. There is no need for the unit to preheat.
This snow machine has been designed to function on a mains power supply of either 120V~60Hz or
230V~50Hz and has been fitted with a suitable power plug for use with your local voltage. Check the label
on the unit and the power plug for the correct voltage.
Always monitor fluid level as running the machine with no fluid could cause permanent damage.
As with most electrical equipment, it is advised that the effect be used in well ventilated areas taking care
not to obstruct the air vents.
·
Never use any other type of liquid other than UNSCENTED water based snow fluid.
· Use of any other fluids or additives will void the warranty.
Maintenance & Servicing
Work on internal parts should be carried out by a qualified technician. Removal of any covers is considered
a breach of warranty and will not be covered under any such agreement unless authorized first by
CHAUVET
• Eyebolt for Safety Cable
• Sock
On the Rear
• Socket for Remote Control
(In/Out)
• DMX In/Out
• Blower Lo/High
• Manual Snow button
• On/Off Switch
• Power Cord Socket and
Fuse holder
1 2 3 4 5 6 7 8 9 10
Off
On
Value
1 2 4 8 16 32 64
128 256
1.Set SW 10 to OFF.
2. Count the value of the switches in the on position.
and SW 4 equals 8.
3. Set SW 3 and SW 4 to the ON position. (4 + 8 = 12)