Filter
Top Products
9
Operation (Continued)
sliding down and streaking. Wait a
couple of minutes for the detergent
to break down the dirt and grime.
Use a brush to lightly scrub heavily
soiled areas. Never allow the deter-
gent to dry on the cleaning surface.
2a. To rinse or to return the nozzle to
high pressure, release the trigger and
slide the nozzle to the high pressure
setting.
2b.For units with quick connect tips:
replace black 65
o
tip with another
color tip.
Never make the
nozzle pressure
adjustment when the gun is triggered.
Adjusting the high-low nozzle when the
gun is triggered can result in damage to
the seals in the nozzle.
Never replace quick
connect tip when
gun is triggered.
3. After using detergents, flush the suc-
tion system by placing the detergent
suction tube into a bucket of clean
water.
You can control the cleaning power of
your pressure washer in two ways:
1. Adjust the spray pattern at the noz-
zle. Choose the widest pattern possi-
ble for spraying when starting the
job and adjust the pattern to a nar-
rower angle until you find a suitable
pattern.
2. The easiest way to regulate the
cleaning power of your pressure
washer is by changing the distance
from the surface you are cleaning.
Begin spraying with a wide fan pat-
tern while standing several feet from
the surface. Slowly move closer to the
object you are cleaning, adjusting the
spray pattern as necessary, until you
find the most effective cleaning tech-
nique.
NOTE: Some units also may have a reg-
ulator knob on the pump that can
adjust the pressure (if so equipped).
!
WARNING
NOTICE
5. Cleaning Power
The final rinse should start at the bottom
and work upward. Make sure that you
thoroughly rinse the surface and that you
remove all detergent.
1. Be sure all detergent is flushed from
system.
2. Turn the engine OFF.
3Turn the water supply OFF.
4. After the engine and water supply are
turned off, trigger the gun to depres-
surize the system.
NEVER turn the
water supply off
before turning the engine/motor off.
Serious damage could occur to the pump
and/or engine/motor.
NEVER disconnect
the high pressure
discharge hose from the machine while
the system is pressurized. To depressurize,
turn engine/motor off, turn water supply
off and squeeze gun trigger 2-3 times.
5. After each use, wipe all surfaces of the
pressure washer with a clean, damp
cloth.
• Do not store the pressure washer out-
doors.
• Do not store the pressure washer
where it might freeze unless it has
been properly winterized (See page 9,
third column).
LONG TERM STORAGE INSTRUCTIONS
(MORE THAN 30 DAYS IN STORAGE)
1. Remove fuel from the tank and run the
pressure washer in a normal operating
mode until the engine stops from a
lack of fuel. Normal operating mode
means actually spraying water from the
gun while the engine is running.
Alternate method – Add fuel stabiliz-
er to gas in the tank and run in nor-
mal operating mode for at least five
minutes.
2. Stop the engine, turn off the water
supply, and trigger the gun to release
pressure in the high-pressure hose.
!
CAUTION
NOTICE
3. Disconnect the water supply and high
pressure hose from the pump.
4. Allow the engine to cool.
5. Disconnect the spark plug wire and
remove the spark plug.
6. Pour 1/2 oz. of engine oil into the
spark plug hole.
Never pull the
starter rope on the
engine when the spark plug is removed
unless the spark plug hole is covered. Fuel
vapor from the hole can ignite by a spark.
7. Place a rag over the spark plug hole
and slowly pull the starter rope several
times to distribute the oil.
WINTERIZING INSTRUCTIONS
1. Follow and complete the Long Term
Storage Instructions on Page 9.
2. Disconnect the spark plug wire.
3. Disconnect the high pressure hose
from the pump.
4. Insert a 12” to 14” piece of garden
hose into the pump inlet.
5. Place a funnel in the other end of the
garden hose.
!
WARNING
8. Storage
6. Final Rinse
7. Shutdown
PRESSURE RELIEF
PROCEDURE
To reduce the risk of bodily
injury or property damage,
always follow this procedure
whenever spraying is stopped,
when work is completed, and
before checking or repairing any
part of the system.
1. Engage the trigger safety latch.
2. Turn the unit off.
3. Remove the ignition cable from
the spark plug.
4. Shut off the water supply.
5. Disengage the trigger safety
latch and trigger the gun to
relieve pressure.
6. Re-engage the trigger safety
latch.
7. Before overnight storage, long
term storage, or transporting
unit, disconnect the water supply
and turn off the fuel supply
valve.
www.chpower.com