Filter
Top Products
10
5
Operation
Severe damage
to electric starter
is possible if you
continue to crank
for more than
5 seconds without
a cool-down.
The temperature
of muffler and the
surrounding areas
may exceed 150o F.
Avoid these areas
WARNING
Electric Starter(if equipped)
Some models of the snow thrower may be equipped
with an optional 120 volt A.C. electric starter. This
electric starter, with a three-wire power cord and plug, is
designed to operate on 120 volt AC household current.
Follow the steps below to use the electric starter.
Cold Start:
1. Determine whether your house wiring is a three-wire
grounded system. Ask a licensed electrician if you
are not certain.
WARNING: The electric starter must
be properly grounded at all times to
avoid the possibility of electric shock
to the operator. If your house wiring
system is not a three-wire grounded
system, do not use this electric starter
under any conditions.
2. If your house wiring system is grounded and a three-
hole receptacle is not available at the point the snow
thrower starter will normally be used, one should be
installed by a licensed electrician.
NOTE: When connecting the power cord, always connect
cord to starter on engine first, then plug the other end
into a three-hole grounded 120 Volt receptacle. When
disconnecting the power cord, always unplug the end
from the three-hole, grounded receptacle first.
3. Attach spark plug wire to spark plug.
4. Make sure that the auger control and the drive
control are disengaged.
5. Remove the keys from the plastic bag. Push key into
the ignition slot. Do not turn the key. Keep second
key in a safe place.
6. Move the choke knob to FULL choke position.
7. Move throttle control to the FAST position.
8. Turn fuel valve on, if so equipped.
9. Connect power cord to the switch box on engine.
10. Plug the other end of the power cord into a three-
hole, grounded 120 volt AC receptacle.
11. Push primer button three times.
12. Push down on the starter button until the engine
starts. Do not crank for more than 5 seconds at a time.
WARNING: Severe damage to electric
starter is possible if you continue to
crank for more than 5 seconds without
a cool-down.
13. When the engine starts, release the starter button
and slowly rotate the choke to OFF position. If the
engine falters, rotate the choke to FULL and then
gradually to OFF.
NOTE: When engaging the electric starter, a slight
hesitation of a few seconds may occur before the
engine starts to turn. This is normal and is not harmful
to the engine.
14. Disconnect the power cord from the receptacle first
and then from the switch box on the engine.
15. Allow the engine to warm up for a few minutes
because the engine will not develop full power until it
reaches operating temperature.
NOTE: If the starter motor runs but the engine does not
turn over, the starter gear may have frozen. Place the
snow thrower in a warmer part of the garage or storage
shed till the gear is free of the accumulated ice.
Warm Start:
1. If restarting a warm engine, rotate choke to OFF
instead of FULL and press the starter button. Do not
push the primer button.
Before Stopping
1. Run engine for a few minutes to help dry off any
moisture on engine.
2. To avoid possible freeze-up of the starter, follow these
steps:
Recoil Starter
a. With the engine running, pull the starter rope with
a rapid, continuous full arm stroke three or four times.
Electric Starter (if equipped)
a. Connect power cord to switch box, then to 120
Volt AC receptacle.
b. While the engine is running, push the starter
button and spin the starter for several seconds.
c. Disconnect power cord from the receptacle first,
then from the snow thrower.
NOTE: The unusual sound from pulling the starter rope or
from spinning the starter will not harm the engine.
3. While standing in the operator’s position (behind the snow
thrower), engage the auger control for a few seconds to
clear any remaining snow and ice from the chute assembly.
To Stop The Snow Thrower
1. To stop the wheels, release the drive control.
2. To stop throwing snow, release the auger control.
3. To stop engine, push throttle control lever to OFF or
pull out the key(either method works). Do not turn key.
WARNING: The temperature of muffler
and the surrounding areas may exceed
150º F. Avoid these areas
Auger Control Test
IMPORTANT: Perform the following test before operating
the snow thrower for the first time and at the start of each
winter season.
Check the adjustment of the auger control as follows:
1. When the auger control is released and in the
disengaged “up” position, the cable should have very
little slack, but should NOT be tight.