Filter
Top Products
Part No. 890313 Form No. F010396D
Page 5 of 12
Nozzle Height Fine Adjustment For Hard Surface
Use: Optimum nozzle height is 1/2" (12.7mm) above ground with
engine not running. To adjust height, loosen screws (item 37), on
quad plate. Prop front of nozzle up 1.0" (25.4mm) above ground.
Keeping wheels on ground, re-tighten screws (item 37). Recheck
and fine adjust to obtain 1/2" (12.7mm) at nozzle front (see fig 1).
Wearing Eye Protection and Durable
Gloves is recommended while operating
chipper.
Use caution when using chipper
Adjustment
Lowers
Nozzle
Rod In
First Hole
Adjustment
Raises Nozzle
(fig. 1)
Item 37 Ref. Securely
Tighten, postion slots toward
unit. Can be reversed to
provide better hole alignment
if required.
Under normal circumstances, allow time for machine
to clear all wood from chipper hopper before stopping
engine. Otherwise, remaining pieces of wood will jam
inside of chipper when engine stops. (See Tamper page 7).
Disconnect spark plug wire.
Remove debris bag quick disconnect from debris outlet on
machine.
Wearing durable gloves, access impeller through
debris outlet on fan housing and rotate impeller
counter clock wise to dislodge and remove jam and
remove debris from hopper with tongs or equivalent.
Reconnect debris bag quick disconnect to machine.
Reconnect spark plug wire.
VACUUM NOZZLE HEIGHT ADJUSTMENT: is
raised and lowered by pushing slightly downward on
handle and pulling height adjust rod (item 23) up at left rear
of machine.
FOR MAXIMUM PICKUP: Adjust nozzle close to debris,
but without blocking airflow into the nozzle.
NOTE
: Never bury
nozzle into debris.
CLEARING A CLOGGED NOZZLE
& EXHAUST: Turn engine off and wait for impeller to
stop completely and disconnect spark plug wire.
Wearing durable gloves, remove clog. Danger, the
clog may contain sharp materials. Reconnect spark
plug wire.
ENGINE: See engine manufacturer’s instructions
for type and amount of oil and gasoline used.
Engine must be level when checking and filling oil and
gasoline.
ENGINE SPEED: Controlled by throttle lever on the handle.
Under normal conditions, operate at minimum throttle to
accomplish your current cleaning task.
FUEL VALVE: Move fuel valve to "ON" position (when
provided on engine).
CHOKE: Operated with throttle control (Honda only).
PRIMER: Push primer per engine instructions ( B&S only).
THROTTLE: Move remote throttle control to fast position.
Pull starting rope to start engine.
IF YOUR UNIT FAILS TO START:
See Troubleshooting on page 12.
INTENDED USE: This machine is designed for vacuuming
leaves, grass clippings and other types of organic litter and
for chipping brush, limbs, corn and sunflower stalks and
palm fronds.
Debris mixed with cans, bottles and small amounts of sand
can be vacuumed; however, it is not this machine's primary
purpose. Vacuuming cans, bottles and sand will affect the
longevity of your machine.
PUT OIL IN ENGINE BEFORE STARTING.
Inspect machine work area and machine before operat-
ing. Make sure that all operators of this equipment are
trained in general machine use and safety.
Do not operate if excessive vibration occurs. If excessive
vibration occurs, shut engine off immediately and check for
damaged or worn impeller, loose impeller bolt, loose impeller
key, loose engine or lodged foreign objects. Note: See parts
list for proper impeller bolt torque specifications. (See trouble
shooting section on page 12).
Your
TERMITE
® chipper is designed to process tree branches
and limbs up to 2" (50.8mm) diameter.
(50.8 mm)
Maximum
Diameter
2
"
Several small branches can be grouped together and fed
together into the chipper (see fig 2.).
When feeding forked branches, squeeze forks together and
feed into chipper entrance (DO NOT overload). If forks are too
large, use a pair of loppers to trim forks down to size. A lopper
storage bracket is provided on every unit (loppers are not
included)
1616
1616
16
Operation
STARTING
16.116.1
16.116.1
16.1
VACUUMING OPERATION
16.216.2
16.216.2
16.2
16.816.8
16.816.8
16.8
CLEARING A CLOGGED CHIPPER HOPPER
CHIPPING OPERATION
16.716.7
16.716.7
16.7
Like all mechanical tools, reasonable care must
be used when operating machine.