Billy Goat QB882 Blower User Manual


  Open as PDF
of 8
 
Part No. 430187 Form No. F060496C
Page 8 of 8
MAINTENANCE
Clear clog.
Solution
Problem Possible Cause
TROUBLESHOOTING
Before Requesting Service Review These Suggestions
Air intake or exhaust clogged.
Abnormal vibration.
Loose or out of balance impeller or loose engine.
Check impeller and replace if required. Check Engine.
Poor air performance
Check stop switches, throttle, choke position and gasoline. Connect
spark plug wire. Clean or replace air cleaner. Or contact a qualified
service person.
Engine will not start.
Stop switch off (Honda only). Throttle in off position. Engine not
in full choke position (Honda only). Out of gasoline. Bad or old
gasoline. Spark Plug wire disconnected. Dirty air cleaner.
Engine is locked, will not
pull over.
Engine problem.
Contact an engine servicing dealer for engine problems.
1717
1717
17
Use only a qualified mechanic for
any adjustments, disassembly or
any kind of repair .
DISCONNECT SPARK PLUG WIRE
BEFORE SERVICING UNIT.
WARNING: TO AVOID PERSONAL INJURY, ALWAYS
TURN MACHINE OFF, MAKE SURE ALL MOVING
PARTS COME TO A COMPLETE STOP.
ENGINE: See engine manufacturer
operator's instructions.
RECONNECT SPARK PLUG WIRE AND
GUARDS BEFORE STARTING ENGINE.
1. Wait for engine to cool and disconnect spark plug.
2. Remove front wheel (item 23),and front wheel bracket
(item 27).
3. Remove housing front plate (item 4), by removing nine
(9) screws (item 12), around outside of front plate.
4. Remove impeller bolt and lock washer.
NOTE: DO NOT PULL OR PRY ON IMPELLER BLADES.
5. Pull on center hub backplate area only of impeller. If
impeller slides off freely, proceed to (step 8).
6. Place two crowbars between center hub backplate area
of impeller and housing on opposite sides. Carefully pry
impeller away from engine until it loosens.
Using a
penetrating oil can help loosen a stuck impeller.
7. If the impeller does not loosen, obtain a 1” (25.4mm)
longer bolt of the same diameter and thread type as the
impeller bolt. Thread longer bolt by hand into the crank-
shaft until bolt bottoms. Using a suitable gear or wheel
puller against the bolt head and the impeller back-plate
(near the blades), remove impeller from shaft.
8. Reinstall new impeller in reverse order of removal.
9. Tighten impeller bolt. Torque impeller bolt (see parts
list on page 7 for proper impeller bolt torque specifica-
tions).
2020
2020
20
IMPELLER REMOVAL
17.217.2
17.217.2
17.2
Engine (See Engine Manual)
Check for excessive vibration
Maintenance Schedule
Maintenance Opera-
tion
Follow these hourly maintenance intervals.
Inspect for loose parts
Inspect for worn or damaged parts
17.117.1
17.117.1
17.1
Lubricate wheels
Every
Use
Every 5 hrs.
or (Daily)
Every 25
hrs.
TIRE AIR PRESSURE: Check at regular intervals and
maintain.
Rear Tires only - 30 Psi. (21 kPa).
Engine Service and Warranty
Contact your nearest engine manufacturer's
authorized servicing dealer.
22.122.1
22.122.1
22.1
Purchased
from
Purchase
Date
2121
2121
21
Serial Plate
Record your machine model, serial number
and date-of-purchase and where purchased
R
min
-1
Operator
1803 S. Jefferson
P.O. Box 308
Lee's Summit,
MO 64063 / USA
Tel (816) 524-9666
Fax (816) 524-6983
Model Serial No.
Unit(Weight) Engine Power
lbs. kg kW rpm
2222
2222
22
Please fill in the WARRANTY CARD and send the upper part to Billy Goat.
The WARRANTY terms are stated on the lower part which remains with the
user. Whenever a Billy Goat Machine is faulty due to a defect in material
and / or workmanship, the owner should make a warranty claim as follows:
The Machine should be taken to the dealer from whom it was
purchased or to an authorized Billy Goat dealer.
The owner should present the remaining half of the Warranty
Registration Card, or, if this is not available, the invoice or receipt.
The Warranty Claim will be filled in by the authorized Billy Goat Dealer,
who will send it with the faulty part to Billy Goat headquarters.
The Quality / Service department at Billy Goat headquarters will study
the claim and parts and will notify their conclusions.
The decision by the Quality / Service department at Billy Goat
headquarters to approve or reject a Warranty claim is final and
binding.
Note:
To process a Warranty Claim, it is necessary to quote the Model
& Serial number who are printed on the Billy Goat Serial Plate.
BILLY GOAT INDUSTRIES INC.
P.O. BOX 308 (1803 S JEFFERSON LEE'S SUMMIT, MO. 64063 / USA
PHONE: 816-524-9666 FAX: 816-524-6983
R
WARRANTY PROCEDURE
89
96
 previous