White Rodgers 1F87-361 Manual

Open as PDF

next previous

1F87-361

Programmable Electronic Digital Thermostat

INSTALLATION AND

OPERATION INSTRUCTIONS

FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY

BEFORE INSTALLING OR OPERATING THIS CONTROL COULD CAUSE

PERSONAL INJURY AND/OR PROPERTY DAMAGE.

DESCRIPTION

• Temperatureoverrideuntilnextprogramperiod

• Manualprogramoverride(HOLDtemperature)

• TemporaryHOLD

• °F/°Cconvertibility

• Temperaturerange45°to90°F

• RC,RH,C,W,Y,G,OandBterminals

• OptionalCterminal(DualPoweroption)

• BandOterminalsforsinglestageheatpumps(noauxiliary

heat)ordamperoperation

• Programstorageincaseofpowerloss

• 2“AA”Energizer

alkalinebatteriesincluded

Operator: Save these instructions for future use!

YournewWhite-Rodgers7-DayDigitalThermostatuses the

technologyofasolid-statemicrocomputertoprovideprecise

time/temperaturecontrol.Thisthermostatoffersyoutheexibility

todesignheatingandcoolingprogramsthattyourneeds.

Features:

• Separateprogramforeachdayoftheweekwithfourseparate

time/temperatureperiodsperday

• Simultaneousheatandcoolprogramstorage

• Preprogrammedtemperaturecontrol

• Backlitdisplay

• LCDcontinuouslydisplayssetpoint,andalternatelydisplays

timeandroomtemperature

PRECAUTIONS

Thisthermostatisintendedforusewithalowvoltagesystem;

donotusethisthermostatwithalinevoltagesystem.Ifindoubt

aboutwhetheryourwiringismillivolt,line,orlowvoltage,haveit

inspectedbyaqualiedheatingandairconditioningcontractor

orelectrician.

Donotexceedthespecicationratings.

Allwiringmustconformtolocalandnationalelectricalcodes

andordinances.

Thiscontrolisaprecisioninstrument,andshouldbehandled

carefully.Roughhandlingordistortingcomponentscouldcause

thecontroltomalfunction.

▲

CAUTION

To prevent electrical shock and/or equipment damage,

disconnect electric power to system at main fuse or

circuit breaker box until installation is complete.

▲

WARNING

Do not use on circuits exceeding speciﬁed voltage.

Higher voltage will damage control and could cause

shock or ﬁre hazard.

Do not short out terminals on gas valve or primary

control to test. Short or incorrect wiring will damage

thermostat and could cause personal injury and/or

property damage.

Thermostat installation and all components of the system

shall conform to Class II circuits per the NEC code.

SPECIFICATIONS

ELECTRICAL DATA

Electrical Rating:

 8to30VAC50/60Hz.orD.C.

 0.05to1.0Amps(Loadperterminal)

1.5 Amps Maximum Total Load(Allterminalscombined)

THERMAL DATA

Setpoint Temperature Range: 

 45°Fto90°F(7°Cto32°C)

Operating Ambient Temperature Range:

 32°Fto105°F

Operating Humidity Range:

 0to90%RH(non-condensing)

Shipping Temperature Range:

 -4°Fto149°F

APPLICATIONS

Forusewith:

• Standardheat/coolorheatonlysystems

• Electricheatsystems

• Gasoroilredsystems

• Gassystemswithintermittentignitiondevices(I.I.D.)

 and/orventdampers

• Hydronic(hotwaterorsteam)systems

• Single-stageheatpumpsystems(noauxiliaryheat)

• Millivoltsystems

DO NOT USE WITH:

• Multi-stagesystems

• Systemsexceeding30VACand1.5amps

• 3-wirezonedhydronicheatingsystems

PART NO. 37-6763B

Replaces37-6763A

1006