TP-Link TL-WR710N Weather Radio User Manual


 
WiFi Pocket Router/AP/TV Adapter/Repeater
MODEL NO. TL-WR710N
Package Contents
QIG
WiFi Pocket Router/AP/TV Adapter/Repeater
MODEL NO. TL-WR710N
Resource CD
Ethernet Cable
TL-WR710N
Quick Installation Guide
7106504563 REV2.0.0
Instant Wireless Connection
Physical Description
Hardware Connection
Wireless Router Mode (Default)
Create a wireless network from an Ethernet
connection. This mode is suitable for dorm
rooms or homes where there's already a wired
router but you need a wireless hotspot.
Create an instant private wireless network
and share Internet to multiple Wi-Fi
devices.This mode is suitable for hotel rooms
and home networks.
Access Point Mode
2
1
After hardware connection, please write down the
Wireless Password and SSID on the label of your
Router for later use. Both are case-sensitive.
SSID
: Default Wireless Network Name
*
Wireless Password/PIN
: Default Password
*
LAN/WAN
: Must use this port to connect to your Modem while in
Router mode. For all other modes, use it as an additional LAN port.
Reset
It is used to reset the Router to its factory defaults.
Indication
TL-WR710N LED:
Status
Solid Green
Blinking
For more detailed information about
Reset
, please refer to
Appendix: Troubleshooting
.
Client Mode
3 4
WISP Client Router Mode
Use as a client router to receive Internet
access from a Wireless Internet Service
Provider (WISP), and share that access with
local devices.
5
4
Enter the Default Password. Click OK or
Next.
LAN
: Connect your ethernet enabled devices for wired network
access. In client mode, use it to give wireless access to a wired-only
device. In access point mode, use it to receive network access from
your local network.
USB
It is used to connect USB Flash or Hard Disk for le sharing and
Mobile devices for charging.
Repeater Mode
Repeat signal from an existing wireless
network. This mode is suitable to extend
wireless coverage, reaching devices that
were previously too far from your primary
router to maintain a stable wireless
connection.
(Note: if the hotel’s Internet has an
authentication process, you will need to
authenticate only once and only on one
device.)
(Note: if the hotel’s Internet has an authentica-
tion process, you will need to authenticate it
on EACH device.)
The repeated signal will display the same
network name and password as your existing
wireless network.
In this mode, this device can be connected to
another device via Ethernet cable and act as
an adapter to grant your wired devices
access to a wireless network, especially for a
Smart TV, Media Player, or Game console
only with an Ethernet port.
(The examples illustrated below are from Windows 7. If you are using a dierent Windows, or a Mac Operating System, your screenshots may look dierent, but the procedure is the same.)
Reset
LAN/WAN LAN
USB
Protected by
NAT Firewall
Wired Ethernet
Connection
Cable
SSID: def
Connect the plug directly to the TL-WR710N to finish
hardware connection.
The provided power plug may differ from the picture due
to different regional power specifications. Here we use the
EU version as an example.
Note:
System is booting.
The Ethernet Cable or USB Device is
connecting to the product.
The device is working properly.
Cable
Wired Ethernet
Connection
Operation Mode Conguration
3
Choose the Working Mode you need, then click “Next” and
refer to the corresponding mode on the back page for
further instruction.
1
Open a Web browser and go to the page
http://tplinklogin.net. Enter the default User Name
and Password: admin, both in lower case letters.
Click OK.
2
After a successful login, click “Quick Setup” from the menu
to congure your TL-WR710N. Click “Next”.
Go to Start > Control Panel > View
network status and tasks > Change
adapter settings. Right click Wireless
Network Connection, and select
Properties. Double click Internet Protocol
Version 4 (TCP/IPv4) in the item list.
1 4
The gure below indicates you have
successfully connected to your network.
3
Click the Wireless Network icon on your
desktop. Select the Default SSID of the
TL-WR710N, then click Connect.
2
Set up the TCP/IP Protocol in "Obtain an IP
address automatically" and "Obtain DNS
sever address automatically" mode on your
PC. Click OK.
S/N:XXXXXXXXXXXX
Model:TL-WR710N Ver:2.0
Wireless Password/PIN:12345678
SSID:TP-LINK_663D6C
MAC:B0487A663D6C
IC: 8853A-WR710N
FCC ID: TE7WR710N
Default Access:
http://tplinklogin.net
Username: admin
Password : admin
WiFi Pocket Router/AP/TV Adapter/Repeater
S/N:XXXXXXXXXXXX
Model:TL-WR710N Ver:2.0
Wireless Password/PIN:12345678
SSID:TP-LINK_663D6C
MAC:B0487A663D6C
IC: 8853A-WR710N
FCC ID: TE7WR710N
Default Access:
http://tplinklogin.net
Username: admin
Password : admin
WiFi Pocket Router/AP/TV Adapter/Repeater