SkyLink CG5 Garage Door Opener User Manual


 
One 3 volt Lithium type (CR2032)
battery is included.
Replacing the battery.
1. Open the case with a corn.
2. Slide the old battery away from the battery holder.
3. Slide in the new battery with the positive (+) side facing up.
4. Firmly close the case.
Brand Frequency
Chamberlain
®
with learn button color: Purple 315MHz
Chamberlain
®
with learn button color: Orange, Red 390MHz
Genie
®
MultiLink
®
MINI GARAGE DOOR REMOTE
WITH FLASH LIGHT
MODEL : CG5
‘Learn’ Button
Garage Door
Opener (GDO)
1. INTRODUCTION
Thank you for your purchase of the MultiLink
®
garage door remote control,
Model CG5. This remote is designed to work with the Chamberlain
®
“Security +”, Genie
®
“Intellicode” and Chamberlain
®
Billion code. This
remote is also capable to operate the mentioned brands garage door
opener with the newer 315MHz garage door openers or the older one at
390MHz. Please follow the details instructions below in order to setup the
new transmitter to work with your existing opener.
You should find a “learn” button from your existing garage door opener
(the unit with the motor located on the ceiling of your garage). Press and
hold this “Learn” button for 2 seconds and then release. The LED light
located beside the ‘Learn’ button will go on. Then press the garage door
button on your new transmitter for 1 second and then release to activate
it. The LED light on your existing
garage door opener will flash then
go off. Your remote control is now
programmed to your existing garage
door opener and will operate your
garage door.
5. TROUBLESHOOTING
If the garage door cannot be activated, check the followings:
- The red light LED should come on when the button is pressed, if not,
check the battery and its polarity, ensure it is inserted properly.
- Repeat programming again to ensure the new transmitter is programmed.
®
6. OPERATION
Press and hold the plastic case
where it marks “PRESS” to
activate the flash light.
Press the garage door opener
button will activate your garage
door.
Garage Door
Button
2. SELECT THE FREQUENCY
Check with your garage door opener to determine it is
The default frequency setting is at 390MHz. Follow the procedure
below to change this frequency setting.
1. Open up the case with a coin.
2. Remove the frequency jumper.
3. Secure the frequency jumper to
the 2 connector posts.
4. Table below shows the frequency
setting with different jumper
configurations.
Jumper (connected at right 2 posts) 315MHz
Jumper (connected at left 2 posts) 390MHz
Either 315MHz or 390MHz
(check on your garage door
opener)
4. PROGRAMMING
Depends on what brand of garage door opener you have, the brand
jumper setting is different. The brand jumper setting is the red jumper
next to the battery.
Brand Brand jumper setting
Chamberlain
®
with learn button color: Purple, Orange, Red
Genie
®
Once you have setup the frequency and brand setting of your remote
control, following the instructions below to learn the remote to your
garage door opener.
3. SELECT THE BRAND
DO NOT let children use the garage door
transmitter without adult supervision.
Children can injure themselves or others
by the garage door.
8. WARNING
If this transmitter triggers other garage doors in your neighborhood,
change all your transmitters and receiver to a new code setting.
Positive "+"
Up
390MHz
315MHz
Posts 1 & 2 Posts 2 & 3 Posts 3 & 4
Chamberlain
®
with learn button color: Green, White,
Grey, Yellow
390MHz
Chamberlain
®
with learn button color: Green, White,
Grey, Yellow
Connecting Jumper on
posts 1 & 2
Connecting Jumper
on posts 3 & 4
Connecting Jumper on
posts 2 & 3
1 2 3 4 1 2 3 4 1 2 3 4
3. SELECT THE BRAND (CONT)
7. BATTERY