Filter
Top Products
CUSTOMER RESPONSIBILITIES
TRACTOR
Always observe safety rules when performing any mainte-
nance.
BRAKE OPERATION
Iftractor requires more than six (6) feet stopping distance at
high speed in highest gear, then brake must be adjusted.
(See"l'O ADJUST BRAKE" inthe Service and Adjustments
section of this manual).
TIRES
Maintain properair pressure inalltires(See "PRODUCT
SPECIFICATIONS" section of this manual).
Keep tires free of gasoline, oil, or insect controlchemi-
cals which can harm rubber.
• Avoid stumps, stones, deep ruts, sharp objects and
other hazards that may cause tire damage.
NOTE: To seal tire punctures and prevent flat tires due to
slow leaks, tire sealant may be purchased from your local
parts dealer. Tire sealant also prevents tire dry rot and
corrosion.
OPERATOR PRESENCE SYSTEM
Be sure operator presence and interlock systems are work-
ing properly. If your tractor does not function as described,
repair the problem immediately.
• The engine should not start unless the clutch/brake
pedal isfully depressed and attachement clutch control
is in the disengaged position.
• When the engine is running, anyattempt bythe operator
to leave the seat without first setting the parking brake
should shut off the engine.
• When the engine is running and the attachment clutch is
engaged, any attempt by the operator to leave the seat
should shut off the engine.
• The attachment clutch should never operate unless the
operator isin the seat.
BLADE CARE
For best results mower blades must be kept sharp. Replace
bent or damaged blades.
BLADE REMOVAL (See Fig. 11)
• Raise mower to highest position to allow access to
blades.
• Remove blade bolt, lockwasher and flat washer secur-
ing blade.
• Install new or resharpened blade with trailing edge up
towards deck as shown.
IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER
HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL
ASSEMBLY.
• Reassemble blade bolt, lock washer and flat washer in
exact order as shown.
Tighten blade bolt securely (27-35 Ft. Lbs. torque).
IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED.
TRAILING MANDREL
ASSEMBLY
EDGE UP BLADE
CENTER
HOLE
FLAT WASHER\
LOCK WASHER
_"" BLADE BOLT
*A GRADE 8 HEAT TREATED BOLT CAN BE
IDENTIFIED BY SIX LINES ON THE BOLT HEAD.
FIG. 11
TO SHARPEN BLADE (See Fig. 12)
NOTE: We do notrecommend sharpening blade- but ifyou
do, be sure the blade is balanced.
Care should be taken to keep the blade balanced. An
unbalanced blade will cause excessive vibration and even-
tual damage to mower and engine.
• The blade can be sharpened with a file or on a gdnding
wheel. Do not attempt to sharpen while on the mower.
• To check blade balance, you will need a 5/8" diameter
steel bolt, pin, or a cone balancer. (When using a cone
balancer, follow the instructions supplied with bal-
ancer.)
NOTE: Do not use a nail for balancing blade. The lobes of
the center hole may appear to be centered, but are not.
• Slide blade on to an unthreaded portion of the steel bolt
orpin and hold the bolt or pin parallelwith the ground. If
blade is balanced, it should remain in a horizontal
position. If either end of the blade moves downward,
sharpen the heavy end until the blade is balanced.
5/8" BO_ BLADE
OR PIN
FIG. 12
BATTERY
Your tractor has a battery charging system which is suffi-
cient for normal use. However, pedodic charging of the
battery with an automotive charger will extend its life.
• Keep battery and terminals cleaR.
• Keep battery bolts tight.
• Keep small vent holes open.
• Recharge at 6-10amperes for I hour.
16