Filter
Top Products
7
INSTAL L ING ATTACHMENT
HANGER
An attachment hanger is provided for storage
when attachmentis notin use.Toinstallhang-
er on attachment:
1. Remove the shaft cap from the attach-
ment (if present) and discard.
2. Press and hold the locking/release but-
ton.
3. Push hanger onto the attachment until
the locking/release button snaps into the
hole.
OPERA TING POSITION
Boots
Heavy ,
Long Pants
Eye Protection
ALWAYS WEAR:
Cut from your left to your right.
NOTE: This brushcutter attachment is not
designed for use with electric powerheads.
When operating unit with brushcutter a ttach-
ment, clip shoulder strap onto uppershoulder
strapclamp,standasshown andcheck forthe
following:
S W ear eye protection and heavy clothing.
S Keeparms extendedwithright handholding
the trigger handle of powerhead.
S Keep left arm extended with left hand hold-
ing the handlebar.
S Keep unit below waist level.
S Shoulder strap pad should be centered on
your left shoulder and dangersigncentered
on your back.
S Maintain full weight of tool on left shoulder .
S Without bending over , keep the blade near
and parallel to the g round and not crowded in-
to material being cut.
OPERA TING INSTRUCTIONS FOR
BRUSHCUTTER ATTACHMENT
S Blade Thrus t is a reaction that only occurs
when using a bladed unit. This reaction can
cause serious injury such as amputation.
Carefully study this section. It is important that
you understand what causes bla de thrust,
how you can reduce the chance of its occur-
ring, and how you can remain in control of unit
if blade thrust occurs.
S WHAT CAUSES BL ADE THRUST -- Blad e
Thrust can occur when spinning blade con-
tacts anobject thatitdoesnotcut. This contact
causes blade to stop for an instant and then
suddenly move or “thrust” away from object
that was h it. The “thrusting” reaction can be
violent enough to cause operator to be pro-
pelled in any direction and lose control of unit.
The uncontrolled unit can cause serious injury
if blade contacts operator or others.
S WHEN BLADE THRUST OCCURS --
Blade Thrust can occur without warning if
the blade snags, stalls, or binds. This is
more likely to occur in areas where it is diffi-
cult to see the material being cut. By using
the unit properly , the occurrence of blade
thrust will be reduced and the operator will
be less likely to lose control.
S Cutonly grass, weeds, andwoody brush upto
1/2 inch in diameter with weed blade. Do not
let blade contact material itcannot cut such as
stumps, rocks, fences, m etal, et c., or clusters
of hard, woody brush with a diameter greater
than 1/2 inch.
S Useasharpblade.Adullbladeis morelikely
to snag and thrust.
S Cut only at full throttle. The blade will have
maximum cutting power and is less likely to
bind or stall.
S “Feed” the blade deliberately and not too
rapidly.The bladecan thrust away if it is fed
too rapidly.
S Cut only from your left to your right. Cutting on
right side of the shield will throw debris away
from the operator .
S Use the shoulder strap and keep a firmgrip
on the unit with both hands. A properly ad-
justed shoulderstrap willsupport theweight
of the unit, freeing your arms and hands to
control and guide the cutting motion.
S Keep feet comfortably spread apart and
braced for a possible sudden, rapid thrust of
unit. Do not overreach. Keep firm footing and
balance.
S Keep blade below waist level. It will be eas-
ier to maintain control of unit.
S Do notraise theengine aboveyour waistas
the blade can come dangerously close to
your body .
S Do not swing the unit with such force that
you are in danger of losing your balance.
Bring the powerhead engine to cutting speed
before entering the material to be cut.
If the blade does not turn when you squeeze
the throttle trigger of the powerhead, make
sure the attachment is fully inserted into the
coupler.
Always release the throttle trigger and allow
powerhead engine to return to idle speed
when not cutting. The blade should not turn
while the engine is runningat idle.If theblade
turns atidle, do not use your unit.Refer to the
CARBURETOR ADJUSTMENT section of
the powerhead m anualor contact your autho-
rized service dealer.
S Maintain good firm footing while using the
unit. Do this by plantingfeet firmly in acom-
fortable apart position.
S Cut while swinging the upper part of your
body from left to right.
S Asyoumoveforwardtothenextareatocut,
be sure to maintain your balance, and footing.