Pentair VS+SVRS Swimming Pool Pump User Manual


 
IntelliFlo
®
VS+SVRS
Intelligent Variable Speed Pump
The ONLY way to comply with new federal
anti-body entrapment standards and save money
There’s simply no better way to add a Safety Vacuum
Release System (SVRS) to your public pool or spa than
with the new IntelliFlo
®
VS
+
SVRS pump. It helps prevent
suction entrapment and also provides value that no
other solution can.
While other safety solutions represent an added cost,
IntelliFlo is an investment that may potentially save
thousands of dollars in energy costs over its long life.
Standard Features
Replaces 3HP or smaller pumps
Meets ASME A112.19.17 standards for anti-body
entrapment protection
Onboard intelligence senses blockage with auto shutdown
Exclusive breakthrough motor technology provides energy savings
while being safety compliant
8 settable, changeable speeds ranging from 1100 to 3450 RPMs
NSF certified and UL and ETL Listed
9/08 Part #P1-078
©2008 Pentair Water Pool and Spa, Inc. All rights reserved.
1620 Hawkins Avenue
Sanford, NC 27330
Phone: 800-831-7133 Fax: 800-284-4151
www.pentairpool.com
IntelliFlo
®
VS
+
SVRS
Intelligent Variable Speed Pump
PENTAIR POOL PRODUCTS / PARAGON AQUATICS / ACU-TROL / STARK / STA-RITE / BERKELEY / AURORA
Performance
curves
EQ Series
®
High Performance Commercial
0 20 40 60 80 10 0 120 140 160
10 0
90
80
70
60
50
40
30
20
10
0
1 100 RPM
1500 RPM
2350 RPM
3110 RPM
3450 RPM
Flow Rate in U.S. GPM
Total Dynamic Head in Ft. of Water
IntelliFlo
®
VS
+
SVRS
Intelligent Variable Speed Pump
IntelliFlo
®
VS+SVRS Pump
Performance Curves
IntelliFlo
®
VS+SVRS Pump
Pump Body
Volute type back pull out design for ease of working on impeller,
diffuser and seal.
Port Size
- Inlet (Suction): 2 inch - 11 NPT
- Outlet (Discharge): 2 inch - 11NPT
Material
- Glass Filled Polypropylene Thermoplastic with threaded brass
inserts for maximum strength.
-
1
4 inch NPT drain plug of thermoplastic thumbscrew (no tool
required) design on the strainer for winterizing.
Impeller
- Glass Filled Noryl enclosed design for corrosion prevention
and maximum flow efficiency.
- Threaded Brass Insert for maximum strength.
Diffuser
- Glass Filled Polypropylene Thermoplastic material with bronze
impeller wear ring.
- Patented FunnelFlo design for maximum efficiency.
Seal plate
- Glass Filled Thermoplastic material with threaded brass inserts
for strength.
Mechanical Seal
- Type 6A mechanical seal
Base
- Glass Filled Polypropylene Thermoplastic with slotted holes
for easy mounting.
Gaskets
- Buna rubber compression resistant
Bolts, Nuts, and Washers
- Stainless steel
Corrosion Prevention
- All thermoplastic pump for maximum hydraulic performance,
noise reduction, and corrosion prevention.
Hair and Lint Strainer
Basket
- Polypropylene Thermoplastic Basket Colored White for easy
debris removal.
- 7.75 inch tall basket with large open area exceeding the
requirements of NSF for maximum debris removal and efficiency.
Lid
- Clear "see thru" Polycarbonate Thermoplastic Lid for easy view
into the basket area.
Lid Locking Ring
- Glass Filled Thermoplastic.
- Cam and Ramp Design allows for quick and easy access to
the basket.
Motor
Frame and Type
- NEMA 56 Frame Square Flange totally enclosed fan cooled.
- Permanent magnet synchronous motor (PMSM).
Shaft
- DS 8018 Stainless Steel Construction
Thermal Overload Protection
- Thermal Overload Protection provided by the integral motor
control.
Bearings
- Lubricated, double sealed, stainless steel, single row ball
bearings.
Electrical
- 230 Volts, 1 phase, 16 amps maximum 50 or 60 Hertz
- Circuit Breaker Required: 20 amp, 2 pole, 230 Volts
Pump Maximum Thermal Limits
- Ambient Air Temperature: 130˚F
- Liquid Temperature: 104˚ F
MATERIALS AND DESIGN
IntelliFlo
®
VS+SVRS Pump
Recirculation pump shall be Pentair Series Model No. ________
self-priming centrifugal pump,____ phase, 60 Hz.
General Notes
Install pump in a cool, dry, well vented location away from pool
heaters, and chemical storage.
Pump should be firmly mounted with pipe supported to prevent
vibration and undue operational noise.
Allow 12" minimum clearance above lid for servicing.
Allow 12" minimum clearance behind motor for servicing.
Motor overheating may be caused by a voltage drop or
excessive voltage. Be sure that wire size and voltage input is
properly regulated.
Specifications
The recirculation pump shall be a self-priming, centrifugal
design with a hair and lint strainer as shown in the plans.
The pump body and attached hair and lint strainer shall be
constructed of non-corrosive 40% glass filled polypropylene
materials, and close-coupled to an electric motor by means of
a seal plate of the same material. The pump body shall have a
single suction port with a 2" NPT on the hair and lint strainer.
A discharge port of 2" NPT and a winterizing drain port of
1
4"
NPT shall be a part of the design.
The pump shall be a back pull-out design to allow servicing
without disturbing piping. The pump shall have a 40% glass
filled polypropylene diffuser to aid in priming and it shall
contain a bronze wear ring for the impeller. The impeller shall
be of the closed type and Noryl
®
, non-overloading at any point
on the performance curve. The mechanical shaft seal shall be
constructed of ceramic and carbon seal faces, with stainless
steel, brass and Buna N materials in the spring bellows portion.
ENGINEERING SPECIFICATIONS
The impeller shall be secured to the motor shaft by means of a
molded in brass insert and a stainless steel locking screw into
the end of the motor shaft. The pump shall be capable of
operating at up to 42 psi, 104˚ F continuous water temperature,
130˚ F ambient air temperature.
The electric motor coupled to the pump shall be of the NEMA
56 Frame permanent magnet synchronous motor (PMSM) totally
enclosed fan cooled series with stainless steel shaft and double
shielded, single row, lubricated stainless steel ball bearings.
Motors shall be continuous duty rated at 130˚ F (or better)
ambient and be suitable for outdoor installation.
The pump motor shall be a NEMA 56 Frame Square Flange,
totally enclosed fan cooled, PMSM for service on a 230 volt
electric supply. The pump shall be rated for ______ GPM at
____ TDH. The pump shall be tested and certified by a nationally
recognized testing laboratory to conform to National Sanitation
Foundation Standard 50.
The drive meets all CE and FCC requirements for line noise.
Hair and Lint Strainer
The buna strainer shall consist of a polypropylene body, poly
carbonate cover with O-ring seal, and Cam and Ramp
locking
ring, and a strainer basket of mineral reinforced polypropylene
material.
The strainer body shall be 2" NPT suction. The strainer body
shall have a removable drain plug for winterizing.
The strainer basket shall be securely positioned below the
suction inlet of the trap, with access for inspection and
cleaning through a removable trap body lid. The trap body lid
shall be secured by means of a Cam and Ramp
locking ring.