Honeywell HC26A Manual

A SERVICE OF

next previous

INSTALLATION INSTRUCTIONS

69- 157

6

E

F

® U.S. Re

g

istered Trademark

Co

py

ri

g

ht © 2001 Hone

y

well • All Ri

g

hts Reserved

69-1576EF G.H. 9-01 • www.hone

y

well.com/

y

ourhome

Home and Building Control Home and Building Control

Honeywell Honeywell Limited-Honeywell Limitée

1985 Douglas Drive North 35 Dynamic Drive

Golden Valley, MN 55422 Scarborough, Ontario

M1V 4Z9

Printed in U.S.A. on recycled

paper containing at least 10%

post-consumer paper fibers.

HC18A, HC22A, HC26A

Humidifier Pad

APPLICATION

The HC18A, HC22A, and HC26A Humidifier Pads re

p

lace the

humidifier

p

ad in the Hone

y

well Flow-Throu

g

h Humidifiers or

A

p

rilaire® Humidifiers. The humidifier s

p

reads water over the

humidifier

p

ad, and when warm air blows over the water-

soaked area, va

p

or is

g

enerated. As the va

p

or circulates

throu

g

h the house, the relative humidit

y

rises.

INSTALLATION

CAUTION

Personal Injury or Equipment Hazard.

Can cause electrical shock or equipment damage.

Disconnect

p

ower su

pp

l

y

before installin

g

or servicin

g

.

Turn off water su

pp

l

y

.

IMPORTANT

Do not remove the powder from the new humidifier

pad. The powdery coating on the pad promotes

water dispersement.

1.

Remove the humidifier cover. See Fi

g

. 1.

2.

Remove the humidifier

p

ad assembl

y

from the humidi-

fier b

y

g

ras

p

in

g

the assembl

y

and

p

ullin

g

it toward

y

ou.

3.

Pr

y

o

p

en the frame at the corners until the PerfectFlo™

water distribution tra

y

lifts off.

4.

Gentl

y

p

inch the water nozzle catches inward until the

water nozzle can be lifted off the tra

y

.

5.

Slide the humidifier

p

ad out of the frame.

RECYCLE NOTICE

This humidifier

p

ad is rec

y

clable. After removin

g

the

p

ad from the humidifier, wash off the

p

owder and

rec

y

cle the

p

ad with the aluminum rec

y

clables.

IMPORTANT

Be careful not to punch the frame to prevent leaking.

6.

Carefull

y

scra

p

e an

y

mineral de

p

osits from the tra

y

and

frame. Be sure nothin

g

is blockin

g

the frame drain hole.

7.

Reattach the water nozzle to the PerfectFlo™ water dis-

tribution tra

y

.

8.

Insert the new humidifier

p

ad into the frame.

IMPORTANT

Be sure the black line on the top of the humidifier pad

is facing up.

9.

Re

p

lace the water distribution tra

y

. Be sure all four tabs

are in

p

lace.

10.

Place the humidifier

p

ad assembl

y

in the humidifier

housin

g

and

p

ress until the assembl

y

is com

p

letel

y

sealed. Be careful not to

p

inch or kink the water feed

tube.

Fig. 1. Humidifier components.

11.

Re

p

lace the humidifier cover.

12.

Turn on the

p

ower and water su

pp

l

y

.

13.

To verif

y

the humidifier o

p

eration, refer to the Owner’s

Guide Checkout Procedure section.

M12371A

PerfectFlo“ WATER DISTRIBUTION TRAY

WATER FEED NOZZLE

HUMIDIFIER PAD

HUMIDIFIER

HOUSING

COVER

FRAME

WATER

FEED

TUBE