Hilme FG250 Swimming Pool User Manual


 
Models FG225
FG250
IMPOR
TANT! PLEASE READ
CAREFULL
Y AND SAVE.
This user’
s manual contains important information
about your Smoke Alarm’
s operation. If you are
installing this Smoke Alarm for use by others,
you must leave this manual—or a copy of it
—with the end user
.
AGENCY PLACEMENT RECOMMENDATIONS
NFPA 72 (National Fire Code) Chapter 11
“For your information, the National Fir
e Protection Association's Standard 72,
r
eads as follows:”
“11.5.1 One- and T
wo-Family Dwelling Units.”
“11.5.1.1 Smoke Detection. Wher
e required by applicable laws, codes, or
standar
ds for the specified occupancy, approved single- and multiple-station
Smoke Alarms shall be installed as follows: (1) In all sleeping rooms.
Exception: Smoke Alarms shall not be r
equired in sleeping rooms in existing
one- and two-family dwelling units. (2) Outside of each separate sleeping area,
in immediate vicinity of the sleeping rooms. (3) On each level of the dwelling
unit, including basements Exception: In existing one- and two family dwelling
units, approved Smoke Alarms powered by batteries are permitted.”
“A.11.8.3 Are More Smoke Alarms Desirable? The required number of Smoke
Alarms might not pr
ovide reliable early warning protection for those areas
separated by a door from the areas protected by the required Smoke Alarms.
For this reason, it is recommended that the householder consider the use of
additional Smoke Alarms for those ar
eas for increased protection. The additional
areas include the basement, bedrooms, dining room, furnace room, utility room,
and hallways not pr
otected by the required Smoke Alarms. The installation of
Smoke Alarms in kitchens, attics (finished or unfinished), or garages is not
normally recommended, as these locations occasionally experience conditions
that can r
esult in improper operation.”
Califor
nia State Fire Marshal (CSFM)
Early war
ning detection is best achieved by the installation of fire detection
equipment in all rooms and areas of the household as follows: A Smoke Alarm
installed in each separate sleeping ar
ea (in the vicinity, but outside bedrooms),
and Heat or Smoke Alarms in the living rooms, dining rooms, bedrooms,
kitchens, hallways, finished attics, furnace rooms, closets, utility and storage
rooms, basements, and attached garages.
LOCATIONS TO AVOID FOR SMOKE ALARMS
For best performance, it is recommended you AVOID installing Smoke
Alar
ms in these ar
eas:
Where combustion particles are produced. Combustion particles form when
something bur
ns. Areas to avoid include poorly ventilated kitchens, garages,
and fur
nace rooms. Keep units at least 20 feet (6 meters) from the sources
of combustion particles (stove, furnace, water heater, space heater) if
possible. In ar
eas where a 20-foot (6 m) distance is not possible – in modular,
mobile, or smaller homes, for example – it is r
ecommended the Smoke
Alarm be placed as far from these fuel-burning sources as possible. The
placement r
ecommendations are intended to keep these Alarms at a
r
easonable distance fr
om a fuel-burning source, and thus reduce “unwanted”
alarms. Unwanted alarms can occur if a Smoke Alarm is placed directly next
to a fuel-bur
ning source. Ventilate these areas as much as possible.
In air streams near kitchens. Air currents can draw cooking smoke into the
sensing chamber of a Smoke Alarm near the kitchen.
In very damp, humid or steamy areas, or directly near bathrooms with
showers. Keep units at least 10 feet (3 meters) away fr
om showers,
saunas, dishwashers, etc.
Where the temperatures are regularly below 40˚ F (4˚ C) or above 100˚ F
(38˚ C), including unheated buildings, outdoor r
ooms, por
ches, or unfinished
attics or basements.
In very dusty, dirty, or greasy areas. Do not install a Smoke Alarm directly over
the stove or range. Keep laundry r
oom Smoke Alarms fr
ee of dust or lint.
Near fresh air vents, ceiling fans, or in very drafty areas. Drafts can blow
smoke away fr
om the unit, preventing it from reaching the sensing chamber.
In insect infested areas. Insects can clog openings to the sensing chamber
and cause unwanted alarms.
Less than 12 inches (305mm) away from fluorescent lights. Electrical “noise”
can interfere with the sensor.
In “dead air” spaces. “Dead air” spaces may prevent smoke from reaching
the Smoke Alarm.
A
voiding Dead Air Spaces
“Dead air” spaces may prevent smoke from reaching the Smoke Alarm.
T
o avoid dead air spaces, follow the installation r
ecommendations below
.
On ceilings, install Smoke Alarms as close to the center of the ceiling as
possible. If this is not possible, install the Smoke Alarm at least 4 inches
(102 mm) from the wall or corner.
For wall mounting (if allowed by building codes), the top edge of Smoke
Alarms should be placed between 4 inches (102 mm) and 12 inches (305 mm)
from the wall/ceiling line, below typical “dead air” spaces.
On a peaked, gabled, or cathedral ceiling, install the first Smoke Alarm within
3 feet (0.9 meters) of the peak of the ceiling, measured horizontally. Additional
Smoke Alarms may be r
equir
ed depending on the length, angle, etc. of the
ceiling's slope. Refer to NFP
A 72 for details on requirements for sloped or
peaked ceilings.
SPECIAL COMPLIANCE CONSIDERA
TIONS, Continued
2. Multi-Family or Mixed Occupant Residence:
Apartment building, condominium. This Smoke Alarm is suitable for use in
individual apartments or condos, pr
ovided a primary fire detection system
already exists to meet fire detection requirements in common areas like
lobbies, hallways, or porches. Using this Smoke Alarm in common areas
may not pr
ovide sufficient warning to all residents or meet local fire
protection ordinances/regulations.
3. Institutions:
Hospitals, day care facilities, long-term health care facilities. This Smoke
Alarm is suitable for use in individual patient sleeping/resident rooms,
pr
ovided a primary fire detection system already exists to meet fire
detection requirements in common areas like lobbies, hallways, or porches.
Using this Smoke Alarm in common areas may not provide sufficient
war
ning to all residents or meet local fire protection ordinances/regulations.
4. Hotels and Motels:
Also boarding houses and dormitories. This Smoke Alarm is suitable for
use inside individual sleeping/resident rooms, provided a primary fire
detection system already exists to meet fire detection requirements in
common areas like lobbies, hallways, or porches. Using this Smoke Alarm
in common areas may not provide sufficient warning to all residents or
meet local fir
e protection ordinances/regulations.
LIMITATIONS OF SMOKE ALARMS
Smoke Alarms have played a key r
ole in reducing deaths resulting from
home fir
es worldwide. However, like any warning device, Smoke Alarms
can only work if they are properly located, installed, and maintained, and
if smoke r
eaches them. They are not foolproof.
Smoke alar
ms may not waken all individuals.
Practice the escape plan
at least twice a year
, making sure that everyone is involved – from kids to
grandpar
ents. Allow children to master fire escape planning and practice
befor
e holding a fire drill at night when they are sleeping. If children or
others do not r
eadily waken to the sound of the smoke alarm, or if there
ar
e infants or family members with mobility limitations, make sure that
someone is assigned to assist them in fir
e drill and in the event of an
emer
gency. It is recommended that you hold a fire drill while family
members are sleeping in order to determine their response to the sound
of the smoke alarm while sleeping and to determine whether they may
need assistance in the event of an emer
gency.
Smoke Alar
ms cannot work without power.
Battery operated units can
-
not work if the batteries ar
e missing, disconnected or dead, if the wrong
type of batteries are used, or if the batteries are not installed correctly.
AC units cannot work if the AC power is cut of
f for any reason (open fuse
or circuit breaker, failure along a power line or at a power station, electrical
fire that burns the electrical wires, etc.). If you are concerned about the
limitations of battery or AC power
, install both types of units.
Smoke Alar
ms cannot detect fires if the smoke does not reach the
Alar
ms.
Smoke fr
om fires in chimneys or walls, on roofs, or on the other
side of closed doors may not reach the sensing chamber and set off the
alarm. That is why one unit should be installed inside each bedr
oom or
sleeping ar
ea—especially if bedroom or sleeping area doors are closed
at night—and in the hallway between them.
Smoke Alar
ms may not detect fire on another floor or area of the
dwelling.
For example, a stand-alone unit on the second floor may not
detect smoke fr
om a basement fire until the fire spreads. This may not
give you enough time to escape safely. That is why recommended
minimum pr
otection is at least one unit in every sleeping area, and every
bedr
oom on every level of your dwelling. Even with a unit on every floor,
stand-alone units may not provide as much protection as interconnected
units, especially if the fire starts in a remote area. Some safety experts
r
ecommend installing interconnected AC powered units with battery
back-up (see “About Smoke Alarms”) or professional fire detection
systems, so if one unit senses smoke, all units alarm. Interconnected
units may pr
ovide earlier warning than stand-alone units since all units
alarm when one detects smoke.
Smoke Alarms may not be heard. Though the alarm horn in this unit
meets or exceeds current standards, it may not be heard if: 1) the unit is
located outside a closed or partially closed door
, 2) r
esidents r
ecently
consumed alcohol or drugs, 3) the alarm is drowned out by noise from
stereo, TV, traffic, air conditioner or other appliances, 4) residents are
hearing impair
ed or sound sleepers. Special purpose units, like those
with visual and audible alarms, should be installed for hearing impair
ed
residents.
Smoke Alarms may not have time to alarm before the fire itself
causes damage, injur
y
, or death, since smoke from some fires may
not r
each the unit immediately. Examples of this include persons
smoking in bed, children playing with matches, or fires caused by
violent explosions r
esulting fr
om escaping gas.
Smoke Alar
ms ar
e not foolpr
oof.
Like any electr
onic device, Smoke
Alarms ar
e made of components that can wear out or fail at any time.
You must test the unit weekly to ensure your continued protection. Smoke
Alarms cannot prevent or extinguish fires. They are not a substitute for
property or life insurance.
Smoke Alarms have a limited life. The unit should be replaced
immediately if it is not operating pr
operly. You should always replace a
Smoke Alarm after 10 years fr
om date of pur
chase. W
rite the pur
chase
date on the space provided on back of unit.
SPECIAL COMPLIANCE CONSIDERA
TIONS
This Smoke Alarm alone is not a suitable substitute for complete fir
e
detection systems in places housing many people—like apartment
buildings, condominiums, hotels, motels, dormitories, hospitals, long-term
health car
e facilities, nursing homes, day car
e facilities, or gr
oup homes of
any kind—even if they were once single-family homes. It is not a suitable
substitute for complete fire detection systems in warehouses, industrial
facilities, commer
cial buildings, and special-purpose non-r
esidential
buildings which r
equir
e special fir
e detection and alarm systems.
Depending on the building codes in your ar
ea, this Smoke Alarm may
be used to pr
ovide additional protection in these facilities.
The following infor
mation applies to all four building types below:
In new construction, most building codes r
equire the use of AC or AC/DC
powered Smoke Alarms only. In existing construction, AC, AC/DC, or DC
powered Smoke Alarms can be used as specified by local building codes.
Refer to NFP
A 72 (National Fir
e Alarm Code) and NFP
A 101 (Life Safety
Code)
, local building codes, or consult your Fir
e Department for detailed
fire protection requirements in buildings not defined as “households.”
1. Single-Family Residence:
Single family home, townhouse. It is recommended Smoke Alarms be
installed on every level of the home, in every bedroom, and in each
bedroom hallway.
Continued...
ABOUT SMOKE ALARMS
Batter
y (DC) operated Smoke Alar
ms:
Pr
ovide pr
otection even when electricity
fails, pr
ovided the batteries ar
e fr
esh and corr
ectly installed. Units ar
e easy to
install, and do not require professional installation. However, they do not provide
inter
connected functionality.
AC powered Smoke Alarms: Can be interconnected so if one unit senses
smoke, all units alarm. They do not operate if electricity fails.
AC with batter
y (DC) back-up:
will operate if electricity fails, pr
ovided the
batteries are fresh and correctly installed. AC and AC/DC units must be installed
by a qualified electrician.
Wireless Interconnected Alarms: Offer the same interconnected functionality
as with hardwired alarms, without wires. Units are easy to install and do not
require professional installation. They provide protection even when electricity
fails, provided the batteries are fresh and correctly installed.
Smoke Alarms for Solar or Wind Energy users and battery backup power
systems:
AC powered Smoke Alarms should only be operated with true or pure
sine wave inverters. Operating this Smoke Alarm with most battery-powered
UPS (uninterruptible power supply) products or square wave or “quasi sine
wave” inverters
will damage the Alarm. If you are not sure about your inverter
or UPS type, please consult with the manufacturer to verify.
Smoke Alar
ms for the hearing impaired:
Special purpose Smoke Alarms
should be installed for the hearing impaired. They include a visual alarm and
an audible alarm hor
n, and meet the r
equirements of the Americans With
Disabilities Act. Can be inter
connected so if one unit senses smoke, all units
alarm.
Smoke alar
ms ar
e not to be used with detector guar
ds
unless the
combination has been evaluated and found suitable for that purpose.
All these Smoke Alarms are designed to provide early warning of fires if located,
installed and cared for as described in the user’s manual, and if smoke reaches
them. If you are unsure which type of Smoke Alarm to install, refer to Chapter 2
of the National Fir
e Pr
otection Association (NFP
A) Standar
d 72 (National Fir
e
Alarm Code) and NFPA 101 (Life Safety Code). National Fire Protection
Association, One Batterymarch Park, Quincy, MA 02269-9101. Local building
codes may also r
equire specific units in new construction or in different areas
of the home.
INTRODUCTION
Thank you for choosing BRK Brands, Inc. for your Smoke Alarm needs.
Y
ou have purchased a state-of-the-art Smoke Alarm designed to provide
you with early war
ning of a fire.
Key featur
es include:
Silence Featur
e (FG250 Only)
- Silences nuisance alarms.
Hinged Cover Design - Allows for fast, easy installation and battery
r
eplacement.
Lighted Power and Alar
m Indicator
- LED r
eassures that the battery is
pr
operly connected and is supplying power. Provides a visual indication
of what unit initiated the alarm.
T
amper Resistant Locking Pin
- Locks alarm cover to pr
event removal
of battery. Perfect for apartment, dormitory or hotel applications.
RV Approved - Approved for use in Recreational Vehicles.
T
est/Silence Button
- One touch button combines both featur
es.
Low Batter
y Indicator
- Beeping signal war
ns when battery needs
r
eplacing.
© 2007 BRK Brands, Inc., a Jarden Corporation company (NYSE: JAH)
3901 Liberty Str
eet Road, Aurora, IL 60504-8122 All rights reserved.
Consumer Affairs: (800) 323-9005 • www.brkelectronics.com • www.firstalert.com
FIRE SAFETY TIPS
Follow safety rules and prevent hazardous situations: 1) Use smoking
materials properly. Never smoke in bed. 2) Keep matches or lighters away
fr
om childr
en; 3) Stor
e flammable materials in proper containers; 4) Keep
electrical appliances in good condition and don’t overload electrical
cir
cuits; 5) Keep stoves, barbecue grills, fireplaces and chimneys grease-
and debris-fr
ee; 6) Never leave anything cooking on the stove unattended;
7) Keep portable heaters and open flames, like candles, away from
flammable materials; 8) Don’
t let rubbish accumulate.
Keep alarms clean, and test them weekly
. Replace alarms immediately if
they are not working properly. Smoke Alarms that do not work cannot alert
you to a fire. Keep at least one working fire extinguisher on every floor, and
an additional one in the kitchen. Have fir
e escape ladders or other r
eliable
means of escape from an upper floor in case stairs are blocked.
BEFORE YOU INST
ALL THIS SMOKE ALARM
IMPORTANT! Read “Recommended Locations for Smoke Alarms”
and “Locations to A
void for Smoke Alarms” befor
e beginning. This unit
monitors the air
, and when smoke r
eaches its sensing chamber, it alarms.
It can give you more time to escape before fire spreads. This unit can
ONL
Y give an early warning of developing fires if it is installed, maintained
and located where smoke can reach it, and where all residents can hear
it, as described in this manual. This unit will not sense gas, heat, or
flame. It cannot pr
event or extinguish fir
es.
Understand The Different Type of Smoke Alarms
Battery powered or electrical? Different Smoke Alarms provide
dif
fer
ent types of pr
otection. See “About Smoke Alarms” for details.
Know Where To Install Your Smoke Alarms
Fire Safety Professionals recommend at least one Smoke Alarm on every
level of your home, in every bedr
oom, and in every bedr
oom hallway or
separate sleeping area. See “Recommended Locations For Smoke
Alarms” and “Locations To Avoid For Smoke Alarms” for details.
Know What Smoke Alarms Can and Can’t Do
A Smoke Alarm can help alert you to fire, giving you precious time to
escape. It can only sound an alarm once smoke reaches the sensor.
See “Limitations of Smoke Alarms” for details.
Check Your Local Building Codes
This Smoke Alarm is designed to be used in a typical single-family
home. It alone will not meet r
equir
ements for boar
ding houses,
apartment buildings, hotels or motels. See “Special Compliance
Considerations” for details.
1 2 3 4 5
HOW TO INSTALL THIS SMOKE ALARM
THE P
ARTS OF THIS SMOKE ALARM
FOLLOW THESE SIMPLE STEPS!
LIMITED WARRANTY
BRK Brands, Inc., ("BRK") the maker of BRK
®
brand and First Alert
®
brand
products warrants that the following model will be free from defects in
material and workmanship:
Models FG225 and FG250 for a period of five years fr
om the date of
purchase.
BRK, at its option, will repair or replace this product or any component of
the pr
oduct found to be defective during the warranty period. Replacement
will be made with a new or remanufactured product or component. If the
product is no longer available, replacement may be made with a similar
pr
oduct of equal or gr
eater value. This is your exclusive warranty
.
This warranty is valid for the original retail purchaser from the date of initial
retail purchase and is not transferable. Keep the original sales receipt.
Proof of purchase is required to obtain warranty performance. BRK dealers,
service centers, or r
etail stor
es selling BRK pr
oducts do not have the right to
alter, modify or any way change the terms and conditions of this warranty.
This warranty does not cover normal wear of parts or damage r
esulting from
any of the following: negligent use or misuse of the product, use on improper
voltage or current, use contrary to the operating instructions, disassembly,
repair or alteration by anyone other than BRK or an authorized service
center. Further, the warranty does not cover Acts of God, such as fire, flood,
hurricanes and tor
nadoes or any batteries that ar
e included with this unit.
BRK shall not be liable for any incidental or consequential damages caused
by the breach of any express or implied warranty. Except to the extent pro-
hibited by applicable law, any implied warranty of merchantability or fitness
for a particular purpose is limited in duration to the duration of the above
warranty. Some states, provinces or jurisdictions do not allow the exclusion
or limitation of incidental or consequential damages or limitations on how
long an implied warranty lasts, so the above limitations or exclusion may
not apply to you. This warranty gives you specific legal rights, and you may
also have other rights that vary fr
om state to state or province to province.
How to Obtain Warranty Service
Service:
If service is required, do not return the product to your retailer.
In order to obtain warranty service, contact the Consumer Affairs Division
at 1-800-323-9005, 7:30 AM - 5:00 PM Central Standar
d Time, Monday
thr
ough Friday. To assist us in serving you, please have the model number
and date of pur
chase available when calling.
For Warranty Service return to: 25 Spur Drive, El Paso, TX 79906
Battery: BRK Brands, Inc. make no warranty, express or implied, written or
oral, including that of merchantability or fitness for any particular purpose
with respect to battery.
Family Gar
d
®
is a r
egister
ed trademark of BRK Brands, Inc.
BRK
®
is a r
egister
ed trademark of BRK Brands, Inc.
First Alert
®
is a registered trademark of the First Alert Trust.
M08-0199-001 A 11/07 Printed in Mexico
All Family Gard
®
Smoke Alarms conform to regulatory requirements,
including UL217 and ar
e designed to detect particles of combustion.
Smoke particles of varying number and size are produced in all fires.
Ionization technology is generally more sensitive than photoelectric
technology at detecting small particles, which tend to be pr
oduced
in gr
eater amounts by flaming fires, which consume combustible
materials rapidly and spread quickly. Sources of these fires may include
paper bur
ning in a wastebasket, or a grease fire in the kitchen.
Photoelectric technology is generally more sensitive than ionization
technology at detecting lar
ge particles, which tend to be pr
oduced
in greater amounts by smoldering fires, which may smolder for
hours before bursting into flame. Sources of these fires may include
cigar
ettes burning in couches or bedding.
For maximum protection, use both types of Smoke Alarms on each
level and in ever
y bedr
oom of your home.
This unit will not aler
t hearing impair
ed r
esidents. It is recom-
mended that you install special units which use devices like
flashing strobe lights to alert hearing impaired residents.
Do not connect this unit to any other alar
m or auxiliar
y device.
It is a single-station unit that cannot be linked to other devices.
Connecting anything else to this unit may prevent it from working
properly.
Unit will not operate without batter
y power
. The Smoke Alarm
cannot work until you install the battery in the correct position
(Match “+” to “+” and “-” to “-”).
This Smoke Alarm has a battery guard which prevents it from
closing unless a batter
y is installed. This warns you the unit will
not operate without a battery.
Do not install this unit over an electrical junction box. Air currents
around junction boxes can prevent smoke from reaching the
sensing chambers and prevent the unit from alarming. Only AC
powered units are intended for installation over junction boxes.
Do not stand too close to the unit when the alarm is sounding.
It is loud to wake you in an emergency. Exposure to the horn at
close range may harm your hearing.
Do not paint over the unit. Paint may clog the openings to the
sensing chambers and prevent the unit from operating properly.
1. “OPEN HERE” tab
2. Cover hinge
3. Test button
4. Power/alarm indicator
T
ools you will need:
• Pencil • Drill with 3/16” (5 mm) drill bit
• Hammer
• Standard flathead screwdriver
1. Hold base firmly and pull up on cover tab marked “OPEN HERE.”
This will open the hinged cover. The cover may unsnap from the base
if it's opened too far
. This will not damage the unit—the cover hinge
snaps back into place easily.
2. Hold the Smoke Alarm base against the ceiling (or wall) and make a
mark at the center of each of the mounting slots with a pencil.
3.
Put the unit where it won’t get covered with dust when you drill the
mounting holes.
4. Using a 3/16” (5 mm) drill bit, drill a hole through each pencil mark.
5. Insert the plastic screw anchors (in the plastic bag with screws) into
the holes. T
ap the screw anchors gently with a hammer, if necessary,
until they are flush with the ceiling or wall.
6. Tighten the screws (provided) into the screw anchors, then loosen
them two tur
ns.
7.
Fit the Smoke Alarm over the screw heads as shown. Close cover.
8.
If the Smoke Alarm cover does not line up the way you want it, rotate
the base and r
e-tighten the screws.
9.
Activate the battery. With the cover open, remove and reinstall the
battery so the terminals on the battery match the terminals on the
Smoke Alarm. Match “+” to “+” and “-” to “-.” Push the battery in
until it snaps in secur
ely and cannot be shaken loose.
If the battery is not snapped in completely, the unit cannot receive
battery power
. The Smoke Alarm may beep briefly when you install
the battery—this is normal.
Once the battery is installed, the r
ed power indicator light (behind the
test button) will flash once a minute to show you the Smoke Alarm is
working.
10.
Close the cover all the way.
11.
Test the Smoke Alarm. See “Weekly Testing.”
T
o lock/unlock the cover to the base:
1. Using needle-nose pliers or a utility knife, detach locking
pin fr
om back of alarm base.
2.
Insert locking pin into the slot located on the front of the
alarm as shown in the diagram.
3.
Remove pin to unlock and replace battery.
Printed in Mexico M08-0199-001 A 11/07
Cover Open
1. “Open Here”
2. Test button or Test/Silence
button (FG250 only)
3.
Smoke alarm base
4. “No Battery” tab
5.
Mounting slots
6.
Install 9V battery here
7. Locking pin slot
BA
TTERY POWERED
SMOKE ALARM
USER’S MANUAL
LISTED
TO
UL 217
Model FG225
Model FG250
Locking Pin
Insert Locking Pin
LOCKING FEA
TURE
WEEKL
Y TESTING
NEVER use an open flame of any kind to test this unit. You
might accidentally damage or set fire to the unit or to your home.
The built-in test switch accurately tests the unit’s operation as
r
equired by Underwriters Laboratories, Inc. (UL).
If the Alarm ever fails to test properly, replace it immediately.
Pr
oducts under warranty may be returned to the manufacturer
for r
eplacement. See “Limited Warranty” for details.
DO NOT stand close to the alar
m when the horn is sounding.
Exposur
e at close range may be harmful to your hearing. When
testing, step away when horn starts sounding.
It is important to test this unit every week to make sure it is working
properly.
Using the test button is the recommended way to test this
Smoke Alarm. Pr
ess and hold the test button on the cover of the unit until
the alarm sounds (the unit may continue to alarm for a few seconds after
you r
elease the button). If it does not alarm, make sur
e the unit is receiving
power and test it again. If it still does not alarm, r
eplace it immediately.
During testing you will hear a loud, repeating horn pattern: 3 beeps, pause,
3 beeps, pause; and the Red LED
will flash rapidly
.
IF THIS SMOKE ALARM SOUNDS
RESPONDING TO AN ALARM
During an alar
m, you will hear a loud, r
epeating hor
n patter
n:
3 beeps, pause, 3 beeps, pause; and the Red LED will flash rapidly.
If the unit alarms and you are not testing the unit, it is warning you
of a potentially danger
ous situation that r
equir
es your immediate
attention. NEVER ignor
e any alar
m. Ignoring the alarm may result
in injury or death.
Never remove the batteries from a battery operated Smoke Alarm
to stop an unwanted alarm (caused by cooking smoke, etc.).
Removing batteries disables the alarm so it cannot sense smoke,
and r
emoves your protection. Instead open a window or fan the
smoke away fr
om the unit. The alarm will reset automatically.
If the unit alarms get everyone out of the house immediately.
REGULAR MAINTENANCE
This unit has been designed to be as maintenance free as possible, but
there are a few simple things you must do to keep it working properly.
Use only the replacement batteries listed below. The unit may not
operate properly with other batteries. Never use rechargeable
batteries since they may not provide a constant charge.
Test it at least once a week.
Clean the Smoke Alarm at least once a month; gently vacuum the
outside of the Smoke Alarm using your household vacuum’
s soft
brush attachment. T
est the Smoke Alarm. Never use water, cleaners
or solvents since they may damage the unit.
If the Smoke Alarm becomes contaminated by excessive dirt, dust
and/or grime, and cannot be cleaned to avoid unwanted alarms,
replace the unit immediately.
Relocate the unit if it sounds frequent unwanted alarms. See
“Locations to A
void for Smoke Alarms” for details.
When the battery becomes weak, the Smoke Alarm unit will “chirp”
about once a minute (the low battery warning). This low battery warning
should last 7 days, but you should r
eplace the battery immediately
to
continue your pr
otection.
Note: If locking pin is engaged see "Locking
Feature" section for unlocking instructions.
Choosing a replacement battery:
Y
our Smoke Alarm r
equir
es one standard 9V battery. The following
batteries are acceptable as replacements: Duracell #MN1604, (Ultra)
#MX1604; Eveready (Energizer) #522. You may also use a Lithium battery
like the Ultralife U9VL-J for longer service life between battery changes.
These batteries are available at many local retail stores.
Actual service life depends on the Smoke Alarm and the environment
in which it is installed. All the batteries specified above are acceptable
r
eplacement batteries for this unit. Regar
dless of the manufactur
er’
s
suggested battery life, you MUST replace the battery immediately once
the unit starts “chirping” (the “low battery warning”).
RECOMMENDED LOCATIONS FOR SMOKE ALARMS
Installing Smoke Alarms in Single-Family Residences
The National Fire Protection Association (NFPA), recommends one Smoke
Alarm on every floor, in every sleeping area, and in every bedroom. In new
construction, the Smoke Alarms must be AC power
ed and inter
connected.
See “Agency Placement Recommendations” for details. For additional
coverage, it is recommended that you install a Smoke Alarm in all rooms,
halls, storage ar
eas, finished attics, and basements, where temperatures
normally remain between 40˚ F (4˚C) and 100˚ F (38˚C). Make sure no door
or other obstruction could keep smoke from reaching the Smoke Alarms.
More specifically, install Smoke Alarms:
On every level of your home, including finished attics and basements.
Inside every bedroom, especially if people sleep with the door partly
or completely closed.
In the hall near every sleeping area. If your home has multiple
sleeping ar
eas, install a unit in each. If a hall is mor
e than 40 feet
long (12 meters), install a unit at each end.
At the top of the first-to-second floor stairway, and at bottom of the
basement stairway.
Specific r
equir
ements for Smoke Alarm installation vary fr
om state to
state and fr
om r
egion to r
egion. Check with your local Fire Department
for current requirements in your area.
It is recommended AC or AC/DC
units be inter
connected for added pr
otection.
INSTALLING SMOKE ALARMS IN MOBILE HOMES & RVS
For minimum security install one Smoke Alarm as close to each sleeping area
as possible. For more security, put one unit in each room. Many older mobile
homes (especially those built before 1978) have little or no insulation. If your
mobile home is not well insulated, or if you are unsure of the amount of
insulation, it is important to install units on inside walls only. Smoke Alarms
should be installed where temperatures normally remain between 40˚ F (4˚ C)
and 100˚ F (38˚ C).
WARNING: Test units used in RVs after the vehicle has
been in storage, before every trip, and once a week while in use. Failure
to test units used in RVs as described may remove your protection.
IF YOU SUSPECT A PROBLEM
Smoke Alarms may not operate pr
operly because of dead, missing or
weak batteries, a build-up of dirt, dust or grease on the Smoke Alarm
cover, or installation in an improper location. Clean the Smoke Alarm as
described in “Regular Maintenance,” and install a fr
esh battery, then test
the Smoke Alarm again. If it fails to test properly when you use the test
button, or if the pr
oblem persists, r
eplace the Smoke Alarm immediately
.
If you hear a “chirp” once a minute, r
eplace the batter
y.
If you experience frequent non-emergency alarms (like those
caused by cooking smoke), try relocating the Smoke Alarm.
If the alar
m sounds when no smoke is visible, tr
y cleaning or
relocating the Smoke Alarm. The cover may be dirty.
If the alar
m does not sound during testing, tr
y installing a new
battery, and make sure it is snapped in securely.
If the Smoke Alarm is still not operating properly, and it is still under
warranty
, please see “How to Obtain W
arranty Service” below
.
Do not tr
y fixing the alarm yourself – this will void your warranty!
WHAT TO DO IN CASE OF FIRE
Don’
t panic; stay calm. Follow your family escape plan.
Get out of the house as quickly as possible. Don’t stop to
get dressed or collect anything.
Feel doors with the back of your hand before opening them.
If a door is cool, open it slowly. Don’t open a hot door. Keep doors
and windows closed, unless you must escape through them.
Cover your nose and mouth with a cloth (preferably damp).
Take short, shallow breaths.
Continued...
WHA
T TO DO IN CASE OF FIRE, Continued
Meet at your planned meeting place outside your home,
and do a head count to make sur
e everybody got out safely.
Call the Fire Department as soon as possible from outside.
Give your addr
ess, then your name.
Never go back inside a burning building for any reason.
Contact your Fire Department for ideas on making your home safer.
Alar
ms have various limitations. See "Limitations of Smoke Alarms"
for details.
This unit is designed to be
mounted on the ceiling, or
on the wall if necessary
.