Filter
Top Products
GRID APPLICATION
Mix 2 2/3 pounds of DuPont™ VELPAR® DF with sufficient
water to make one gallon of suspension and thoroughly agitate.
Intermittent agitation may be required to maintain the
VELPAR® DF in suspension.
Apply the VELPAR® DF suspension directly to the soil surface
in a grid pattern using an exact delivery handgun applicator.
This equipment delivers a thin stream of predetermined volume.
VELPAR® DF should be applied during the period from
hardwood bud break to early summer.
Application rate and grid pattern will depend on soil texture and
woody plant composition. Use the lower rates on coarse
textured soils and when the major component of the hardwoods
are susceptible species. Use the high rates on fine-textured soils
and where weeds identified in the label as “partial control or
suppression” predominate.
Application Patterns and Rates For VELPAR® DF
Suspension
ML/Spot Grid (Ft) Lb/Acre
Coarse 0.5 3 X 4 1.3*
1.2 3 X 6 2
2.1 4 X 6 2.6
Medium/Fine 1.2 3 X 34
2.3 3 X 6 4
1.6 3 X 3 5.3
3.1 3 X 6 5.3
* Use on deep sands with pines four years or more of age.
BASAL (SOIL)
SINGLE STEM TREATMENT
Mix 2 2/3 pounds of VELPAR® DF with sufficient water to
make one gallon of suspension and thoroughly agitate. Apply
the VELPAR® DF suspension with an exact-delivery handgun
applicator. This equipment delivers a thin stream of
predetermined volume when triggered. Apply the VELPAR®
DF suspension at the rate of 2 to 4 ml for each inch of stem
diameter at breast height. Direct the treatment to the soil within
3 feet of the root collar of woody plants to be controlled.
For multi-stemmed and low-growing brush that have stem
diameter
s that are difficult to determine, apply the VELPAR®
DF suspension at the ra
te of 2 to 4 ml per 3 f
eet of canop
y
width. For tall, slender (columnar) brush types, apply 4 to 8 ml
per 3 feet of height. Base the rate on whichever canopy
dimension is gr
ea
ter (width or height).
Apply the lower volumes
f
or coar
se te
xtur
ed soils or low organic matter soils and the
higher volumes for fine textured soils or high organic matter
soils.
When treating brush that requires more than a single delivery of
the VELPAR® DF suspension, apply subsequent deliveries
equall
y spaced ar
ound the target plant. If treating brush on
sloping sites, apply most of the suspension on the uphill side of
the stem. If treating resprouts from brush disturbed by cutting or
other mechanical methods,
the rate of application should be
proportional to the original tree size, not just the size of sprout
regrowth.
USE PRECAUTIONS
RELEASE - GRID & SINGLE STEM
•
Application of VELPAR® DF spots closer than 36 inches to
conifer seedlings in their first season or directly up slope from
these seedlings may result in injury or mortality.
• Use VELPAR® DF on seedlings in their first or fourth year
and older. Injury may result from use on two and three year
old seedlings where root growth is extensive but hardiness is
lacking.
RELEASE
HERBACEOUS WEED CONTROL
VELPAR® DF is recommended for controlling herbaceous
weeds where the following species are grown:
EASTERN US
WESTERN US
APPLICATION INFORMATION
EASTERN US
Apply VELPAR® DF as a broadcast or banded spray in the
spring prior to conifer bud break to lessen conifer injury
potential.
WESTERN US
Rainbelt (areas of high spring rainfall): For best results, apply
as a br
oadcast or banded spr
ay in the late winter or spring when
weeds are actively growing, but prior to conifer budbreak. If
application is made after conifer bud break, use directional spray
equipment to prevent contact with conifer foliage, as injury may
r
esult.
Snowbelt (areas of low spring rainfall): For best results, apply
as a broadcast or banded spray in the fall before soil freezes and
after the f
inal r
esting bud has hardened on the conifers. Or,
spring applications may be made after snow cover melts in
anticipation of rainfall prior to conifer budbreak. Weed control
r
esults from spring treatments will be dependent on sufficient
rainfall following application to activate VELPAR® DF.
USE RATES
The rates listed below are for broadcast application. For band
application, use proportionately less. For example, use 1/2 of
the broadcast rates when treating a 3-foot band where row
spacing is 6 feet. Use the higher rate range for the harder to
control (*Suppression) weeds listed in the table below.
Blue spruce
Douglas fir
Engleman spruce
Grand fir
Jeffrey pine
Lodgepole pine
Noble fir
Ponderosa pine
Sitka spruce
Western hemlock
White fir
Loblolly pine
Longleaf pine
Slash pine
Red pine
16