Filter
Top Products
CEILING/WALL VENTILATION FAN
READ AND SAVE THESE INSTRUCTIONS
GENERAL SAFETY INFORMATION
1. Make sure that the electric service supply voltage is
AC 120V, 60Hz.
2. Follow all local electrical and safety codes, as well as
the Nation Electrical Code (NEC) and the Occupation
Safety and Health Act (OSH Act).
3. Always disconnect the power source before working
on or near the ventilating fan, motor or junction box.
4. Protect the power cord from sharp edges, oil, grease,
hot surfaces, chemicals or other objects.
5. Do not kink the power cord
.
6. Do not install the unit where ducts are congured as
shown in Fig. A.
7. Provide suction parts with proper ventilation.
8. This unit is UL listed for use over a bathtub or shower
when installed in a GFCI protected branch circuit.
9. These ventilating fans are intended for residential
usage only.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manu
facturer.
2. Before servicing or cleaning unit, switch power o at
service panel and lock the service disconnecting
means to prevent power from being switched on
accidentally. When the service disconnecting means
cannot be locked, securely fasten a prominent
warning device, such as a tag, to the service panel.
3. Installation work and electrical wiring must be done
by qualied person(s) in accordance with all
applicable codes and standards, including re-rated
construction.
4. Sucient air is needed for proper combustion and
exhausting of gases through the
ue (chimney) of
fuel burning equipment to prevent back drafting.
Follow the heating equipment manufacturer’s
guideline and safety standards such as those
published by the National Fire Protection Association
(NFPA), and the American Society for Heating,
Refrigeration and Air Conditioning Engineers
(ASHRAE) and the local code authorities.
5. When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. If this unit is to be installed
over a tub or shower, it
must be marked as appropriate for the application
and be connected to a GFCI (Ground Fault Circuit
Interrupter) – protected branch circuit.
8. Do not use this unit with any other solid-state control
devices. Solid-state control devices may cause
harmonic distortion, which can cause a motor
humming noise.
9. NEVER place a switch where it can be reached from a
tub or shower.
10. Not to be installed in a ceiling thermally insulated to
a value greater than R40. (This is req
uired for
installation in Canada only).
Turning angle too large Duct shrink
Too many elbows Elbow near the body
Body
CAUTION
1. For general ventilating use only. Do not use to
exhaust hazardous or explosive materials and vapors.
2. Not for use in cooking areas. (Fig. B)
3. This product must properly connect to the
grounding conductor of the supply circuit.
4. To reduce the risk of injury to persons, install the fan
at least 8.2 feet (2.5m) above the oor.
4
5
Cooking area
4
5
Do not install above or
inside this area
Cooking
Equipment
floor
SUPPLIED ACCESSORIES
Part name Appearance Quantity
Grille
1
Motor
1
Housing
1
Duct
Connector
(4”)
1
Screw
(Ø4×25)
4
Screw
(NO.8-32)
1
Suspension
Bracket
1
3 Inches
Adaptor
Connector
1
1. INSTALLATIONS
Proper insulation around the fan to minimize
building heat loss and gain.
MOUNT HOUSING WITH FLANGE(CELING/ WALL)
1-1. To bend the housing tabs out to 90 degree
and make housing tabs contact the bottom or
front of the joist.
1-2. The housing mounts with 4 screws (Ø4×25).
Screw housing to joist through the round
holes in each mounting ange, then through
the other holes.
Fig. A
Fig. B
Page 1.
INSTALLATION AND OPERATING INSTRUCTIONS
MODELS SLM80 / SLM100