Crown Audio XTi 1000 Stereo Amplifier User Manual


 
Crown International
1718 W. Mishawaka Rd.
Elkhart, IN 46517-9439
TEL: 574-294-8200
FAX: 574-294-8FAX
www.crownaudio.com
XTi 1000
2/08 139473-1D
Specifi cations subject to change without prior notice. Latest
information available at www.crownaudio.com.
Crown and Crown Audio are registered trademarks of Crown
International, Inc. Printed in U.S.A.
© 2008 Crown Audio
®
, Inc.
Architectural & Engineering Specifi cations
XTi SERIES
XTi 1000
The Crown
®
XTi 1000 power amplifi er shall be a solid-state two-channel
model with a switch-mode universal power supply.
The outputs shall be usable as stereo or bridged-mono modes of opera-
tion. The bridged-mono mode shall bridge the outputs to provide increased
output voltage.
The amplifi er shall contain controlled slew-rate voltage circuitry to protect
it against radio frequency interference burnouts. It shall also be protected
from current overload at its output stage. The slew rate of the amplifi er
shall be greater than 30 volts per microsecond in stereo mode.
The amplifi er shall temporarily go into a standby mode if its power trans-
former becomes excessively hot and shall automatically resume normal
operation once it has cooled to a safe operating temperature.
Front-panel controls shall include a power on/off switch, a detented input
level control for each channel and three buttons for menu navigation of the
front-panel LCD screen and front panel lockout.
The front panel shall have the following indicators:
Signal Indicator: Green LED, one per channel, illuminates when a very
low-level signal is present at input. May be used for troubleshooting cable
runs. –10 Indicator: Green LED fl ashes when output signal exceeds –10
dB below clip. –20 Indicator: Green LED fl ashes when output signal level
exceeds –20 dB below clip. Ready Indicator: Green LED, one per channel,
illuminates when the amplifi er is ready to produce audio. Clip Indicator:
Red LED, one per channel, turns on at the threshold of audible distortion.
Thermal Indicator: Red LED, one per channel, illuminates under excessive
temperature conditions. Power Indicator: Blue LED illuminates when the
amplifi er has been turned on and has power.
The rear panel shall have the following connectors:
AC Line Connector: NEMA 5-15P (15A). Input Connector: XLR, one per
channel. Link/Out Connector: Loop-thru signal from input connector for
linking to another amplifi er, one per channel. Output Connectors: Two
Neutrik
®
Speakon
®
NL4MP (mates with NL4FC) output connectors. Chan-
nel-1 Speakon
®
shall be wired with Ch. 1 and Ch. 2 outputs for use with
optional single 4-conductor cable. Two binding post outputs (in parallel
with Speakon
®
connectors). HiQnet USB Connector: Type B, connects to a
HiQnet network.
The power amplifi er shall meet or exceed the following power criteria at 1
kHz: 2 ohm Stereo (per channel): 700W with 1%THD (not rated for 100V
versions), 4 ohm Stereo (per channel): 500W with 0.5% THD, 8 ohm
Stereo (per channel): 275W with 0.5% THD, 4 ohm Bridge-Mono: 1,400W
with 1% THD (not rated for 100V versions), 8 ohm Bridge-Mono: 1,000W
with 0.5% THD.
The amplifi er shall meet or exceed the following performance criteria:
Voltage Gain at 1kHz, 8 ohm rated output: 30.5 dB. Frequency Response:
+0/–1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms. Load Impedance:
Safe with all types of loads. Rated for 2 to 8 ohms in Stereo mode, 4 to 16
ohms in Bridge-Mono mode. The XTi 1000 A1 (100V version) is rated for
4 to 8 ohms Stereo, 8 to 16 ohms Bridge Mono. Sensitivity: 1.4V. Signal
to Noise Ratio (below rated 1 kHz power at 8 ohms): 100 dB (A weighted).
Damping Factor: Better than 500 from 20 Hz to 400 Hz. Crosstalk: > 70 dB
below rated power, 20 Hz to 1 kHz. Input Stage: Input shall be electroni-
cally balanced and shall employ precision 1% resistors. Input Impedance
(nominal): 20 k ohms balanced and 10 k ohms unbalanced. Maximum
Input Signal: +22 dBu typical. AC Line Current: 6.5A. At idle, the amplifi er
shall draw 90 watts or less. Operating Temperature: 0° C to 40° C at 95%
relative humidity (non-condensing).
The amplifi er shall include Digital Signal Processing with these functions:
Input EQ: 6 parametric fi lters per channel with adjustable Q, ±15 dB boost/
cut. Also adjustable high and low shelving fi lters. This 8-fi lter EQ section
can be bypassed.
Crossover Filters: Highpass and lowpass per channel. Butterworth
6/12/18/24 dB per octave. Linkwitz-Riley 24/48 dB per octave. Also
includes ±15 dB bandpass gain and polarity control.
Delay: For signal alignment of driver; 50 mS total delay.
Subharmonic Synthesizer: Takes the low-frequency content of the input
signal and “synthesizes” a new signal that is the same as the input signal
but one octave lower. The new synthesized signal is then mixed with the
original signal to create the effect.
Output Limiter: Prevents clipping.
Presets: 20 presets, 19 of which are user-defi nable.
The amplifi er shall be safe when driving any kind of load—even highly
reactive ones.
AC line voltage and frequency confi gurations available shall be 100V, 120V,
220-240V, 50/60 Hz.
The amplifi er shall have a rugged steel chassis coated with environmentally
friendly powder. The amplifi er shall be fan-cooled.
The dimensions of the amplifi er shall allow for 19 inch (48.3 cm) EIA stan-
dard (RS-310-B) rack mounting. The amplifi er shall be 3.5 inches (8.9 cm)
tall and 12.25 inches (31.11 cm) deep behind mounting surface.
The amplifi er shall weigh 18.5 lb pounds (8.4 kg).
The amplifi er shall be designated the Crown XTi 1000.