Filter
Top Products
OPERATION
ADD ENGINE OIL:
* Place pressure washer on a level surface and remove
one of the yellow Oil FillCaps (Fig, 17) and add engine
oil from the enclosed bottle unttl level is at point of
overflowing. Check engine oil level before starting
each time thereafter. If oit level is below point of
overflowing, fillto proper level. Crankcase oil capacity
is about 620ml or 21 fluid ounces,
AND OPENING
FIG, 17 ...........
CAUTION: ANY ATTEMPT TO CRANK OR START
THE ENGINE BEFORE IT HAS BEEN PROPERLY
• SERVICED WITH THE RECOMMENDED OIL RE-
SULTS IN AN ENGINE FAILURE.
ADD GASOUNE:
ALWAYSALLOWROOMFORFUELEXPANSION.
! _lb WARNING: NEVER FILL FUEL TANK INDOORS. I
NEVERFiLLFUELTANKWHENENGINEiSRUN-I
NINGORHOT.DONOTLIGHTACIGARETTEORI
SMOKE WHEN FILLING FUELTANK.
• Use regular UNLEADED gasoline with the pressure
washer engine. Regular leaded gasoline may also be
used if UNLEADED isnot available. Fuel tank capacity
is I U.S. gallon.
IMPORTANT: IT IS IMPORTANT TO PREVENT GUM
DEPOSITS FROM FORMING tN ESSENTIAL FUEL SYS-
TEM PARTS SUCH AS THE CARBURETOR, FUEL FIL-
TER, FUEL HOSE OR TANK DURING STORAGE. ALSO,
EXPERIENCE INDICATES THAT ALCOHOL-BLENDED
FUELS (CALLED GASOHOL OR USING ETHANOL OR
METHANOL) CAN ATTRACT MOISTU RE WHICH LEADS
TO SEPARATION AND FORMATION OF ACIDS DURING
STORAGE, ACIDIC GAS CAN DAMAGE THE FUEL SYS-
TEM OF AN ENGINE WHILE IN STORAGE, TO AVOID
ENGINE PROBLEMS, THE FUEL SYSTEM SHOULD BE
EMPTIED BEFORE STORAGE OF 30 DAYS OR
LONGER. SEE "STORAGE" ON PAGE 18. NEVER USE
ENGINE OR CARBURETOR CLEANER PRODUCTS IN
THE FUEL TANK OR PERMANENT DAMAGE MAY OC-
CUR.
• Clean area around fuel fillcap, remove cap.
,, Add =UNLEADED" regular gasoline, slowly, to fuel I
tank.
• Install fuel cap and wipe up any spilled gasoline.
TO TURN ON WASHER
• Attach one end ofa garden hose to a cold water source.
Water supply should not exceed ! 40°F (55°C).
• Check that high pressure hose is attached to pump
outlet and that water supply is attached to pump inlet.
• Turn ON water.
• Press trigger on gun and wand assembly to force air
from high pressure hose.
• Start engine according to "TO START THE ENGINE."
TO START THE ENGINE
IMPORTANT: DO NOT RUN PUMP WITHOUT THE
WATER SUPPLY CONNECTED AND TURNED ON.
,, Start, store and fuel the unit in a level position.
• Open fuel shut-off valve.
Press trigger on pressure washer wand to relieve high
pressure and/or purge the inlet hose of air.
,, Adjust safety latch on spray gun to the ON position.
This disables the trigger so you cannot inadvertently
actuate a high pressure spray (Fig. 18).
TRIGGER _ _ t 'J t \\
t OFF
\
FIG. 18
* Locate the Run!Stop switch (Fig. 19 on Page 13) next
to the engine cylinder head and set it to RUN.
o Close the choke to FULL position (Fig. 20 on Page 13)
by sliding itto far positionin direction indicated by arrow
on air cleaner housing.
t Turn pressure control knob counterclockwise, two
turns from maximum pressure.
e Grasp the starter grip and pull slowly until you feel
resistance. Then pull rapidly.
= When engine starts, move choke lever to "RUN" posi-
tion. If engine fails to start, move choke lever to "RU__
position and pull starter rope (maximum 2 pulls). •
(
. If engine fails to start, repeat the previous two stepsr_
]2