Filter
Top Products
7
en
Unintentional sparking can result in fire or electric shock.
Unintentional start-up can result in entanglement, traumatic
amputation, or laceration.
Fire hazard
WARNING
• Usea3-wireextensioncord.
• First attach extension cord to electric starter connector and then into a wall
receptacle. If additional extension cord is required, use a 3-wire.
• If the supply cord is damaged, it must be replaced by the manufacturer or its
service agent or a similarly qualified person in order to avoid a hazard.
NOTICE: This engine was shipped from Briggs & Stratton without oil. Before you start
the engine, make sure you add oil according to the instructions in this manual. If you
start the engine without oil, it will be damaged beyond repair and will not be covered
under warranty.
Note: Some engines and equipment have remote controls. See the equipment manual
for location and operation of remote controls.
1. Check the oil level. See the How To Check/Add Oil section.
2. Make sure equipment drive controls, if equipped, are disengaged.
3. Turn the fuel shut -off valve, if equipped, to the on position.
4. Turn on the equipment switch (either a rocker (A)orakey(B) switch). See Figure 5.
5. Turn the choke control (C) to the choke
position.
Note: Choke is usually unnecessary when restarting a warm engine.
6. Push the primer (D)twotimes.
Note: Priming is usually unnecessary when restarting a warm engine.
7. Rewind Start: Firmly hold the starter cord handle (E). Pull the starter cord handle
slowly until resistance is felt, then pull rapidly.
Note: If the engine does not start after repeated attempts, go to
BRIGGSandSTRATTON.COM or call 1-800-233-3723 (in USA).
WARNING: Rapid retraction of the starter cord (kickback) will pull y our
hand and arm toward the engine faster than you can let go. Broken bones, fractures,
bruises or sprains could result. When starting engine, pull the starter cord slowly until
resistance is f elt and then pull rapidly to avoid kickback.
8. Electric Start: First connect the extension cord to the power cord receptacle (F,
Figure 6) and then into a wall receptacle. If an additional extension cord is required,
make sure it is a 3-wire.
WARNING: If the extension cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified person in order to avoid a
hazard.
9. Electric Start: Depress the push button (G). After the engine starts, first disconnect
the extension cord from the wall receptacle and then from the power cord receptacle
(F).
Note: If the engine does not start after repeated attempts, go to
BRIGGSandSTRATTON.COM or call 1-800-233-3723 (in USA).
NOTICE: To extend the life of the starter, use short starting cycles (five seconds
maximum). Wait one minute between starting cycles.
10. Allow the engine to warm up for several minutes. Then, slowly move the choke
control to the run
position.
How To Stop The Engine - Figure
5
WARNING
Gasoline and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
• Do not choke the carburetor to stop engine.
1. Turn off the equipment switch (either a rocker (A)orakey(B) switch). See Figure 5.
2. After the engine stops, turn the fuel shut-off valve, if equipped, to the closed position.
Maintenance
Use only original equipment replacement parts. Other parts may not perform as
well, may damage the unit, and may result in injury. In addition, use of other parts
may void your warranty.
We recommend that you see any Briggs & Stratton Authorized Dealer for all
maintenance and service of the engine and engine parts.
NOTICE: All the components used to build this engine must remain in place for proper
operation.
Emissions Control
Maintenance, replacement, or repair of the emissions control devices and systems
may be performed by any non-road engine repair establishment or individual.
However, to obtain “no charge” emissions control service, the work must be performed
by a factory authorized dealer. See the Emissions Warranty.
Unintentional sparking can result in fire or electric shock.
Unintentional start-up can result in entanglement, traumatic
amputation, or laceration.
Fire hazard
WARNING
Before performing adjustments or repairs:
• Disconnect the spark plug wire and keep it away from the spark plug.
• Use only correct tools.
• Do not tamper with governor spring, links or other parts to increase engine
speed.
• Replacement parts must be the same and installed in the same position as the
original parts.
• Do not strike the flywheel with a hammer or hard object because the flywheel
may later shatter during operation.
When testing for spark:
• Use approved spark plug tester.
• Do not check for spark with spark plug removed.
Maintenance Chart
First 5 Hours
• Change oil
Every8HoursorDaily
• Check engine oil level
Every 50 Hours or Annually
• Change engine oil
• Check muffler and muffler guard
Annually
• Replace spark plug
• Replace fuel filter (if equipped)
• Check valve clearance **
** Not required unless engine performance problems are noted.
Carburetor Adjustment
Never make adjustments to the carburetor. The carburetor was set at the factory to
operate efficiently under most conditions. However, if adjustments are required, see any
Briggs & Stratton Authorized Dealer for service.
NOTICE: The manufacturer of the equipment on which this engine is installed specifies
the top speed at which the engine will be operated. Do not exceed this speed.
How To Replace The Spark Plug - Figure
7
Check the gap (A, Figure 7) with a wire gauge (B). If necessary, reset the gap. Install
and tighten thespark plug to the recommendedtorque. For gap setting ortorque, see the
Specifications section.
Note: In some areas, local law requires using a resistor spark plug to suppress ignition
signals. If this engine was originally equipped with a resistor spark plug, use the same
type for replacement.
Not for Reproduction