-
Posted by rhp on Oct 15th, 2008 at 4:28pm
Manual
No problem - just looking for manual
-
Posted by longhours_40 on Oct 15th, 2008 at 9:44am
oil pump
oil pump dont work
-
Posted by ken.haire on Oct 13th, 2008 at 2:54pm
Manual
If anyone has this manual or knows a site where i can get instructions befor i cut my leg off, hehe, please contact me
-
Posted by foster95 on Oct 13th, 2008 at 12:28pm
ignition system wireing
I need the layout of the wireing from the coil to cutoff switch and other leads to ground
-
Posted by stucarol_t on Oct 12th, 2008 at 6:21pm
idle adjustment
need to adjust idle
-
Posted by jluke2044 on Oct 12th, 2008 at 4:29pm
bogging down
Unless it is at wide open throttle, it will bog down, sometimes dying and is then hard to start. Checked plug, cleaned filter. Saw has about 10 hours on it.
-
Posted by ermyers on Oct 11th, 2008 at 2:24pm
air flow
When I put the carb cover back on the saw chokes down. I cannot find any opening for air flow to the bottom of the filter. Where does the air enter the filter chamber?
-
Posted by j.shellenbarger on Oct 10th, 2008 at 8:28pm
Won't stay running
Hard to start, but can get started.After it warms up, wont stay running,acts like it is starving for fuel,when i press the trigger it dies out.I have replaced the fuel filter,and carb diaphragm gasket kit,cleaned carb and needle valve ect,replaced spark plug and it still does'nt keep running
-
Posted by goody on Oct 10th, 2008 at 6:49pm
Ignition module
Saw started and ran fine until yesterday, pulled once, sputtered a little then quit and will not start. chedked plug, it's clean but quite wet, tried to get spark with plug pulled and grounded on chassis, nothing. Suspect ignition module, but wonder if there is any other circuitry that would suppre…
-
Posted by youngblue27 on Oct 10th, 2008 at 3:56pm
parts breakdown
isolator spring broke and I need to know that part number
-
Posted by tammyharris47 on Oct 9th, 2008 at 8:37pm
Cover for chain
Looking for the cover to the chain.
-
Posted by gregorybernard on Oct 8th, 2008 at 2:08pm
Parts Manual
Yes I Own a poulan Chain saw but I dont have the parts Manual anymore. Its a 2550 18 inch. Serial No.96318H600236-2 Ive tried on line could you tell me where its at Id appreciate it. Greg Bernard
-
Posted by jtfreeman on Oct 7th, 2008 at 5:51pm
throttle trigger
I was replacing gas line. Throttle trigger became disengaged. how does the metal cable end attach to the trigger/
-
Posted by dwendt1 on Oct 6th, 2008 at 10:02pm
parts list
I need to locate a muffler
-
Posted by hereford2534 on Oct 5th, 2008 at 8:02am
clutch
lost 1 clutch shoe
-
Posted by hemi_honey on Oct 4th, 2008 at 8:08pm
Chain Oiler
The auto chain oiler isn't working, any ideas?
-
Posted by mike.hefner on Oct 4th, 2008 at 4:34pm
automatice oiler
My poulan 2075 chain saw's auto oil no longer works
I have not used it often
How would I go about fixing it
-
Posted by omopr01 on Oct 3rd, 2008 at 2:40pm
manual
I'm looking for the manual for my saw. Is there one I can download?
-
Posted by txhoborose on Oct 2nd, 2008 at 12:35pm
repair
primer bulb replacement
gas line replacement
-
Posted by ogtaylor1938 on Oct 1st, 2008 at 9:04pm
drive sprocket
replace drive sprocket
-
Posted by dennyv37331 on Oct 1st, 2008 at 8:47pm
Gas Mix
I need to know the oil-fuel ratio
-
Posted by tom.g.bradley on Oct 1st, 2008 at 9:11am
Will Not Idle
After replacing the fuel line the saw will not idle. It runs fine when the trigger is depressed but if released the saw quits. Could the carb be blocked but still run at full speed?
-
Posted by am1946 on Sep 30th, 2008 at 3:44pm
FUEL LINES
PROBLEM FIGURING OUT WHERE FUEL LINES GO
-
Posted by nbh45304 on Sep 29th, 2008 at 7:18pm
service/IT manual
looking for a sercive or an IT manual fof a poulan 1950 model chainsaw
-
Posted by rs822 on Sep 27th, 2008 at 2:47pm
lost manual
need instructions
-
Posted by rs822 on Sep 27th, 2008 at 2:47pm
lost manual
need instructions
-
Posted by jmalcom45 on Sep 27th, 2008 at 1:37pm
Automatic Oiler
I have had the oil supply line repaired recently and now the oiler does not work again. How do I get at the oiler to repair myself?
-
Posted by rich.l.schroeder on Sep 26th, 2008 at 9:05pm
fuel mixture
Gas oil ratio
-
Posted by peterk2 on Sep 26th, 2008 at 2:13pm
Gas/oil mixture
What mixture of gas (octane)and oil (weight) do I use for fuel in a Poulan PP4620AVX.
Thank You.
-
Posted by mharrington on Sep 26th, 2008 at 1:08pm
parts
i have a spring that broke that i think connects the handle to the motor.iam trying to get a parts man. for this mpdel.
-
Posted by sanch68 on Sep 26th, 2008 at 12:59pm
need the instruction booklet
bought this model but it didn't come with the manual
-
Posted by garyg_hosuton on Sep 25th, 2008 at 11:15pm
recoil starter
I need to replace the recoil starter but no one can rewind the silly spring. Strange design. I assumed you could purchase the entire assembly but all I can find is the individual parts.
-
Posted by wallou on Sep 25th, 2008 at 5:07pm
adjusting the carburetor
How do you adjust the two screws on the carb for best gas milage? lol Actually for the best preformance.. Thanks... Rick
-
Posted by cartercarl on Sep 23rd, 2008 at 12:32pm
gas lines
The question I need answered is on this web page but the answer is not. The problem is knowing where to place the new gas lines in the Poulan 2150 chain saw.
-
Posted by m1roy on Sep 22nd, 2008 at 11:35pm
chain lubrication
my chain is not lubricating and is causing the saw to overheat. How do I fix this problem?
-
Posted by zapzme2 on Sep 22nd, 2008 at 1:40pm
carburator adjustment
stalls while idling
-
Posted by airboat9 on Sep 22nd, 2008 at 9:38am
what is the gas mixture
i cant seem to find the ratio of gas and oil for my 2002 poulan3450 i got it used and with no maual
-
Posted by cccvh on Sep 21st, 2008 at 10:20am
owners manual
Is there a web site were I can go to get a copy of the owners manual for a poulan 2550?
-
Posted by mfalter on Sep 20th, 2008 at 10:26pm
Need a copy of the operator's manual
Poulan 16 inch chainsaw operator's manual.
-
Posted by pick3man on Sep 20th, 2008 at 7:48pm
how to adjust carb
run till carb is out of gas then stalls
-
Posted by david.ash50 on Sep 20th, 2008 at 3:05pm
Fuel System
All the gas lines in my chainsaw have rotted. There are some inside the tank and some above the tank to the carbourator. Does anyone have a schematic of how they are supose to go back together? Also where does the duckbill go
-
Posted by lawnranger945034 on Sep 20th, 2008 at 12:09pm
chain installation
borrowed chainsaw from brother, wont cut , i think chain is on backwards, would like to see correct instalation
-
Posted by meadecsa on Sep 19th, 2008 at 7:35pm
muffler/baffle
I lost a bolt while cutting and the entire muffler assembly fell apart. I tried putting it back together but am confused about gasket imprints I see but only have one gasket
-
Posted by ottisv on Sep 18th, 2008 at 7:05pm
gas oil ratio
What is the proper ratio of oil to gas?
-
Posted by dubuc on Sep 18th, 2008 at 12:51pm
fuel line arrangement
need to replace fuel lines
-
Posted by georgealsup on Sep 17th, 2008 at 5:32pm
TO REPLACE CHAIN BREAK ATTACHMENT
I removed my chain break attachment from my saw and have been unable to replace it. Thanks fro any help you may have. '
George
-
Posted by dalbert67 on Sep 17th, 2008 at 4:52pm
rope is tight
i took my new saw out of the box filled with oil for the chain and gas mixed, i pulled the rope and it will not pull at all
-
Posted by billjackson5191 on Sep 16th, 2008 at 8:37pm
Poulan 2050 Chainsaw
I would like to know can I put a 16" bar & chain on a Poulan 2050 chainsaw that came with a 14" bar & chain. If I can will I have to change the sprocket also.
-
Posted by pmpr107 on Sep 15th, 2008 at 10:40am
FUEL LINE REPLACEMENT
CORRECT PLACEMENT OF FUEL LINES
-
Posted by pmpr107 on Sep 15th, 2008 at 10:40am
FUEL LINE REPLACEMENT
CORRECT PLACEMENT OF FUEL LINES
-
Posted by ashcar61 on Sep 15th, 2008 at 10:23am
starter spring
How to recoil starter spring
-
Posted by hgorneault on Sep 14th, 2008 at 10:26pm
oil cap
lost oil cap
-
Posted by wunderwinter on Sep 14th, 2008 at 6:56pm
gas mixture
what is the correct gas mixture for this chain saw, it WON"T start !!!! put a new plug and it still won't start
-
Posted by grantt on Sep 14th, 2008 at 6:17pm
Engine Schematic
I need an engine schematic for the product indicated. Poulon people told me on the phone that I should be able to find it online...no luck so far. Thanks for any help.
-
Posted by schillingm on Sep 14th, 2008 at 3:59pm
Muffer
Need to put muffler back on
-
Posted by thomasimm on Sep 14th, 2008 at 3:55pm
Pull Start
Pull start stuck. How do You free the pull rope
-
Posted by regrundy on Sep 14th, 2008 at 3:53pm
gas mixture
I need to know the gas mixture.
-
Posted by luskmarvin on Sep 14th, 2008 at 1:49pm
chain comes off
chain keeps jumping off
-
Posted by bestigoe on Sep 14th, 2008 at 12:53pm
I need file size and angle to sharpen chain
I need file size and angle to sharpen this saw.
-
Posted by pmp855 on Sep 13th, 2008 at 5:43pm
replace gas lines
correct placement
-
Posted by mtroyer on Sep 13th, 2008 at 3:09pm
starter springs
The small coil sping on the pull starter needs replaced. Where can I find one. Not the larger one, just the small 3/4" by about 1" tall one
-
Posted by dananddee on Sep 13th, 2008 at 2:40pm
piston
Won't start
-
Posted by dvillere on Sep 13th, 2008 at 11:49am
Diagram for carb.
diagram for carb.
-
Posted by ssstott on Sep 12th, 2008 at 1:00am
operators manual
Hi need a operators manual can you help, cheers
-
Posted by onejoanne on Sep 11th, 2008 at 7:57pm
service/user manual
just want a manual to know what to take apart to have chain sharpened
-
Posted by lccompound on Sep 11th, 2008 at 9:09am
part
i lost a washer and i need to get a new one
-
Posted by gainous68 on Sep 10th, 2008 at 11:38pm
need handle
I need the back handle for this model and poulan says it no longer has this part.
-
Posted by paulguillott on Sep 10th, 2008 at 11:26pm
bar and chain
would like a bigger chain.
-
Posted by longbk on Sep 10th, 2008 at 9:17pm
Tech support
I haven't received any reply about my fuel line problem on my 2150 chain saw. Is there a way to get in contact with Poulan tech support for assistance?
-
Posted by janniewannie1952 on Sep 10th, 2008 at 4:38pm
automatic chain oiler does not work
Can this be fixed or do I need to replace the pump?
-
Posted by scorpgg on Sep 10th, 2008 at 11:50am
fuel lines
All the fuel lines were dry rotted. I am trying to replace, need a schematics of how the fuel line runs from tank to primer/carb
-
Posted by pcchad on Sep 8th, 2008 at 2:34pm
replacing oil pump
is the oil pump under the clutch? if so,. how hard is it to remove clutch without special tools?
paul
-
Posted by pcchad on Sep 8th, 2008 at 1:21pm
dry chain
oil pump
-
Posted by stoy17 on Sep 8th, 2008 at 6:06am
starter cord
starter cord gets stuck when fully extended. Wheel needs jolting for cord to spring wind back.
-
Posted by ssatina on Sep 7th, 2008 at 9:56am
Starting
when I am pulling The rope it jerks Is it something serious
can i fix that my self
-
Posted by sweetsurender on Sep 5th, 2008 at 7:29pm
fuel line
How do I connect the fuel lines on my poulan 2150 chainsaw
-
Posted by rwood464 on Sep 3rd, 2008 at 8:55pm
flieing clutch
clutch flies out from saw .i have replaced with new clutch and have replaced the same as i removed it .is there a reason for this to happen
-
Posted by wnebel on Sep 3rd, 2008 at 3:14pm
tighten chain
tighten chain
-
Posted by gasior1 on Sep 2nd, 2008 at 10:49pm
poulan chainsaw
after using it for 90 min it stops and will not start untill it cools down
-
Posted by slim on Aug 30th, 2008 at 9:00pm
pull string
how do you re-assemble the pull start section after the string breaks
-
Posted by determine75 on Aug 30th, 2008 at 5:41pm
clutch
I need to repace the clutch
-
Posted by rjwtwo on Aug 30th, 2008 at 5:10pm
tighten chain
tighten chain
-
Posted by longbk on Aug 30th, 2008 at 4:05pm
fuel lines
trying to replace cracked and broken fuel lines. Is there a diagram to show me where the fuel lines go back into place. I seem to have an extra outlet. Help. Hurrican is on the way.
-
Posted by bayoubarry on Aug 27th, 2008 at 11:15am
chainsaw
motor not getting fire
-
Posted by oconndo on Aug 27th, 2008 at 8:28am
file size
Can anyone tell me what size file to use to sharpen the Poulan 3314?
-
Posted by sr1430 on Aug 26th, 2008 at 1:57pm
NEED A MANUAL FOR p40118wt
OPERATING MANUAL FOR p40118wt
-
Posted by nobrainer1hs on Aug 25th, 2008 at 6:28pm
how to put pully cord back on
pully cord broke
-
Posted by druwill on Aug 24th, 2008 at 2:15am
starter cup and starter rewind
looking to locate and purchase a starter cup and rewind for a model 46 Beaird-Pouland chainsaw which was produced in 1963.
-
Posted by rickbrew on Aug 23rd, 2008 at 6:44pm
Getting it Running
I have had this chain saw for a couple of years and it is always hard to get running. Today, when I really needed it, nada!
-
Posted by shadyguy99 on Aug 20th, 2008 at 6:03pm
carb ajustment
on the low speed ajustment which way is to turn up
-
Posted by frogie8101 on Aug 19th, 2008 at 5:52pm
gaslines
weretheygo
-
Posted by rhickey_00 on Aug 19th, 2008 at 11:28am
Replacement fuel line
How do I replace the fuel line?
-
Posted by rondengel on Aug 18th, 2008 at 6:10pm
need parts
do you have a parts page for the Model 3400 especially need bolts for holding casing on
-
Posted by martinstrome on Aug 18th, 2008 at 2:03pm
how to start engine
I NEED STARTING INSTRUCTIONS
-
Posted by jdboughton45 on Aug 18th, 2008 at 1:21pm
operator manual
need maintenance procedures
-
Posted by animal989 on Aug 18th, 2008 at 8:16am
blade
putting blade on
-
Posted by lfeltman on Aug 17th, 2008 at 10:37pm
i need a manual
i need a manual,my saw won't start.what is the fuel
mix for an older poulan 245a? can i still get parts?
-
Posted by daray on Aug 17th, 2008 at 12:51pm
fuel problem
i have replaced the primer,carb,fuel lines and spark plug. the saw will crank and rev but will only run for a few seconds and seems to run out of gas. have checked all lines for leaks and can find none. do you have any suggestions? thank you dray
-
Posted by tricolino on Aug 17th, 2008 at 11:45am
Chain
What file size should I use to sharpen my chain?
-
Posted by mstrsn on Aug 16th, 2008 at 7:43am
fuel line and primer line routing
When my dad died I got his Poulan 260 Pro, and the fuel and primer lines were crumbling so it was impossible to trace their routing. Could someone please help me to solve this puzzle? Thanks, Mike
Add products and discussions to your stuff and receive a timely personalized email containing updates, tips and solutions for all the
products you own!
What Would Solar Conversion Cost You?
Get Your Home Ready for Winter
Safer Calling on the Road
Copyright © 2008 OwnerIQ, Inc. All Rights Reserved. Designated trademarks and brands are the property of their respective owners.